Mechanical COMMISSIONING ENGINEER
Abu Dhabi National Drilling Company
مجموع سنوات الخبرة :19 years, 7 أشهر
: Responsible for.
(A) COMMISSIONING of the all rig EQUIPMENT, ACCESSORIES
(1) AKER equipment
(a) Mud pumps (TPK 2200) (b) Top drive (DDM1000 -AC-2M)
(c) Draw work (GH 3300 EG-AC 2G ) (d) Rotary table(
( 2 ) FORUM equipment:
(a)Hydraulic cat walk (b)Iron roughneck
(c)XY crane (d)mouse hole ( 3 ) INGERSOLL RAND equipment
(a) Air winches (b) Man Rider (c) BOP hoist
(d) Air compressors (e) Air Dryer
(f) cold start(Engine operated) air compressor
( 4 ) CAT engines
(a) model 3516 (b) model 3512 Emergency generator
( 5 ) NOV. equipment
(a) agitators MA-20& MA-15 & MA-10 (B) shell shakers (c) mud cleaner ( 6 ) MISSION centrifugal pumps (different impeller sizes )
( 7 ) spiral conveyer (Auger)
( 8 ) hydraulic power unit
( 9 ) Fire Fighting Station (10) vertical crane
(11 ) SWACO mixing hopper
(12) oil water separator system
(13 ) DERRICK degasser vacuum (14) Fuel oil Purifier ( Alfa Laval )
(15) EZZ TORQUE hydraulic cat head
(B) - Review the scope of Rig project components and identify any possible abnormal
(C) - Review approved MAR. Of each Equipment before commissioning and Highlight any deviations from the approved MAR to the Project manager.
(D) - Perform all pre commissioning, commissioning and performance testing of the rig equipments and make punch list for any defect or missed point according to approved MAR.
(E) - Closeout of the commissioning documentation including punch list, and handover certificates
(F) - Ensure that any required commissioning activities are planned and scheduled appropriately.
(G) - Provide technical Input into commissioning work if it is necessary depending on my field work experience
: Responsible for. Maintenance of the all rig components, accessories
1- CAT Engines : model- 399 & 398 & 3512 A & 3512 B& 3406 & 3412
2- Blow out preventer (B. o. p): SHAFFER` & CAD &
3- B.O.P closing Unit : (KOOMY 80 & CAD) and its Air pumps & Electric Triplex pump.
4- Well Head Control Valves "CRESMASS TREE"
5 Drilling Equipments : such as
(a) Draw Work : Models (N.O.V & VARCO & DRILL MEC)
(b)Rotary Tables (c) Swivel & Traveling Block & Crown
(d)- TOP DRIVE systems- “T D S -11 NOV “
6- Pneumatic SYSTEM:
(a) compressors (sullair, Ingersoll-Rand, Atlascopco )
(b) Air dryer (sullair, Ingersoll-Rand)
(c) pneumatic control valves ( Bosch, Rexroth ) - directional control - pressure control - flow control
(d) Air service unit ( filter + lubricator )
(e) Pipe lines - pipe fittings - armored hoses
(f) AIR OPERATED EQUIPEMENTS ( Ingersoll-Rand ) : 1- Air winches for tools & Equipments: 5 Tons SWL ( safety working load )
2 - Man Rider Air Winch : 0.5 Ton SWL (safety working load )
- (g)Air operated reciprocating pump - (h)Rotating Mouse Hole (Air Motor)
- (i) Air operated Diaphragm pump(cellar pump) - ( k) AIR CLUTCHES
- (j)Degasser Vacuum pump (Negative pressure pump) - (L)Driller Cabinet ( pneumatic control panel )
7- MUD SYSTEM
- (a) Mud pump ( TRIPLEX Axial piston pump) : 12 inch Suction line & 6 inch Discharge line & high viscous discharge liquid
(1)Engine operated ("Torque Converter & Air Clutch & Compound gears and chains" ) Pneumatic control
(2) Electrical operated (D/C motors with blowers VFD control house ) with cooling water heat exchanger, hydraulic oil heat exchanger
- (b)Centrifugal pumps (with mechanical seal ) :as charging pumps
- (c)Pulsation Damper (HYDREL) - (d) Safety Relief valve (OTTECO & NOV )
- (d)Mud Solids Control Equipments : such as shell shakers & mud cleaners & desalter
- (e)Mud Agitators : (BRANDT N.O.V ”MA-10” - MOTOVARIO)
- (f)Centrifugal pumps( Different Impeller Sizes): with Rubber Seal
- (g)Manual & Hydraulic Control Valves
- (h)Mud Tanks
8 - FUEL SYSTEM
(a) fuel pump ( with Mechanical Seal)
(b) Filtration Unit OR Purifier ( Centrifugal separator ) "ALFA LAVAL" Type
(c) Fuel Tanks
(d) Electro Motion Valves to CUT IN & CUT OUT the pumps
(e) Level Sensors "high & low" to" start & stop " the Electro Motion Valve
9 - WATER SYSTEM
(a)Centrifugal pumps" Different Impeller Sizes" : Types 1- MAGNIUM "Oil Lubrication Gear Box &Bearings"
2- MISSION "Grease Lubrication Gear Box &Bearings"
(b) High Pressure Cleaner "Axial Piston Pump" : Type "NIAGRA"
(c) pipe lines & valves and fittings
10- FIRE FIGHTING STATION " Portable UNIT" Consists of :
(a) TWO Centrifugal PUMPS 1- Diesel Operated & 2- Electrical Operated
(b) Diesel Engine : Model C15
(c) Ejectors ( to mix foam with water with different ratios)
(d) Water Tank (e) FOAM Tank (f) Level Sensors
Supervise, operate and maintain all equipments within EDC working procedures.
Responsible for the management of all equipments, ensuring safe and efficient operation all the time.
Capable of performing all the duties required for maintaining a fully operational onshore / offshore drilling rigs.
Undertake Maintenance reports according to (PMS) and send to appropriate department if required.
Manage the working team planning and performance and ensure that the working hours pass smoothly.
Adhere to company planned preventive maintenance system to Minimize the down time and maximize safety
: Responsible for maintenance for all hydraulic system components
(1) Hydraulic pumps.
(a) gear pumps: internal & external gear pump such as "CASSAPA & parker
(b) axial piston pump: such as Sauer & hydromatic & Kawasaki
(c) Vane pump: such as Eaton
(2) hydraulic motors : all types
(a) axial piston (b) radial motors
(3) hydraulic valves:
(a) directional control valves: Rexroth, parker,
(b) pressure control valves : relief, sequence, pressure reducing valve(P.R.V), counter balance, lock VALVES,
(c) flow control valves : orifice, check
(4) hydraulic transmission
(5) hydraulic torque converter :
Mechanical power Engineering