ABDULLAH TAJ

Senior Electrical/CP QA/QC Engineer (NACE CP2) at NESMA & Partners

• Saudi Arabia - Ras Tanura
• My current job since May 2022

Electrical & Cathodic Protection Quality Control Inspector CBT Passed & Saudi Aramco Approved at EPPM ENGINEERING PROCUREMENT & PROJECT MANAGEMENT (TUNISIAN SAUDI FOR PROJECTS)

• Saudi Arabia - Eastern Province
• My current job since April 2020

Performed QC electrical inspection activities through the implementation of Project quality plan of the
project, covering inspection testing & pre- com activities of electrical.
 Performs QC activities of the project by implementation of the project quality plan, QCPs, ITP, Clients IFC Drawing,
applicable standards and specifications.
 Complies quality reports and recommendations to QA/QC manager for any problem encounter during the
execution of below ground piping installation and the project as a whole.
 Verify detailed records and reports for all Inspections conducted at the Site, and maintain the Quality
Control Documentation. Involving in regular Quality Control meetings with the Contractor & Correlate,
prepare and issue the Weekly Field Inspection Notice to the Contractor and supporting the
Commissioning & Start-Up Team.
 Issued site instructions and (NCR) for unacceptable work practices at site in co-ordinate with the Head
of Department/Design Staff and obtain their comments prior to auctioning.
 Performed Weekly Preservation of MV Booster Pump Motors.
 Performed Weekly Preservation of LV Air Cooler Motors.
 Performed Site Surveillance Inspection.

Electrical QA QC Inspector at SICIM SAUDI ARABIA

• Saudi Arabia - Dhahran Al Janoub
• January 2022 to May 2022

Electrical & Cathodic Protection Quality Control Inspector Saudi Aramco Approved at ENPPI Engineering for the Petroleum and Process Industries

• Saudi Arabia - Eastern Province
• April 2019 to April 2020

Performed QC electrical inspection activities through the implementation of Project quality plan of the
project, covering inspection testing & pre- com activities of electrical.
 Preparation RFI (QMIS) (Request for inspection).
 Performs QC activities of the project by implementation of the project quality plan, QCPs, ITP, Clients IFC Drawing,
applicable standards and specifications.
 Complies quality reports and recommendations to QA/QC manager for any problem encounter during the
execution of below ground piping installation and the project as a whole.
 Performed witness for 60/80 MVA Power Transformer Testing with SPTC Vendor.
 Provide technical assistants during and after the commencement of power transformer installation
as per the Quality control procedure (QCP), approved drawings, specifications and local
authorities regulations. Act as a focal point to the Client.
 Contribute in developing the Project Execution Plan (PEP), implement a Project Quality Plan (PQP)
and prepare a Project Action Plan to govern all phases of the project.
 Provide quality assurance and controls to the EPC contractor activities in all phases of the project.
 Ensuring that all quality documentation is assembled and maintained in accordance with client
approved procedures.
 Inspection of all kind of plant lighting.
 Verify detailed records and reports for all Inspections conducted at the Site, and maintain the Quality
Control Documentation. Involving in regular Quality Control meetings with the Contractor & Correlate,
prepare and issue the Weekly Field Inspection Notice to the Contractor and supporting the
Commissioning & Start-Up Team.
 Installation of under-ground and above-ground conduits, cable trays, duct banks, power, control and
instrument cables.
 Quality Surveillance inspection on Contractor's project execution during different phases of execution.
 Participate as Company representative-specialist on equipment inspection and performance testing
at Vendor's workshop or at sites.
 Ensure verification of inspection performance by: conducting regular inspections, verification of
corrective actions, verification of subcontractor's performance and inspection.
 Implementing Quality Control requirements on construction sites mainly in the installation of Electrical
and Instrumentation systems, Preparation of Quality Control Procedures and Inspection Test Plan in
accordance with SAUDI ARAMCO and applicable International standards.
 Inspection for Transformer Winding Resistance test.
 Material Receiving Inspection for CP system (Sacrificial Anode & ICCP).
 Issued site instructions and (NCR) for unacceptable work practices at site in co-ordinate with the Head
of Department/Design Staff and obtain their comments prior to auctioning.
 Calibration WTI & OTI.
 Inspection for Transformer IR, Ratio, Tan Delta test.
 Inspection for Transformer Pressure/Leakage test.
 Inspection for MV and LV cable trench.
 Inspection for MV cable Duct bank before and after concrete.
 Inspection for MV cable bus Installation, Cable pulling etc.
 Inspection for Grounding cable trench and exothermic welding.
 Inspection for Cable tray installation as per NEMA VE-2.
 Inspection for post insulators installation.
 Inspection for Vacuum circuit breaker HI-POT & Contact Gap test.
 Inspection for L V & MV Switchgears Bus bar HI-POT & Contact Resistance test.
 Inspection for LV & MV Panels tests.(Breaker IR Test, Trip Test & Contact Resistance test)

Electrical & Cathodic Protection Quality Control Inspector Saudi Aramco Approved at CPP (China Petroleum Pipeline Engineering Co. Ltd)

• Saudi Arabia - Eastern Province
• June 2018 to March 2019

Performed QC electrical inspection activities through the implementation of Project quality plan of the
project, covering inspection testing & pre- com activities of electrical.
 Preparation RFI (QMIS) (Request for inspection).
 Complies quality reports and recommendations to QA/QC manager for any problem encounter during the
execution of below ground piping installation and the project as a whole.
 Ensure compliance by al site personal to this procedure to the specific quality plan and the IFC drawing.
 Adhere to the Non-conformance procedure.
 Monitors daily ongoing construction activities and verifies compliance with approved inspection and test
plans, procedures, specification and standard requirement.
 Prepare daily QC records and final inspection acceptance documentation where required, ensure the
procedures are being followed.
 Responsible for inspecting installation & test as defined in the quality control inspection plans of project
standards.
 Ensure the quality is maintained as per Saudi Aramco standards by following the relevant SATIP and SAIC.
 Ensure that the approved QA/QC document is physically available at every site for client inspection.
Executes the activities as per ITP (Inspection Test Plan).
 Review Electrical special process procedure as per Schedule Q.
 Submitting weekly highlights, monthly inspection report to Quality Supervisor.
 Record regular readings and keep records to ensure the potential readings are in line with the project
requirement and report if they are not.
 Conducting Toolbox meetings to familiarize the construction team to execute the electrical
activities as per SAES and applicable international standards.
 Identify and coordinate to close all NCR’s.
 Cathodic Protection for pipelines at Thrust Anchors.
 Cathodic Protection for pipelines Highway road crossing.
 Cathodic Protection for Trunk lines and Transmission lines.
 Bonding box’s installation.
 Cathodic Protection for pipelines at Fence Area.
 Galvanic anode 3 Pin Test station’s installation.
 Typical anode installation for road or camel crossing at existing multiple above grade pipeline crossings.
 Galvanic CP circuit potential testing.
 Conduct the quality inspection Monthly Galvanic CP Circuit potential testing as per Aramco Procedure.
 Bonding of multiple buried parallel pipelines in common corridor.
 Connection of bonding station’s for multiple pipeline crossings.
 Inspection of CP system equipment’s, Transformer Rectifier (ICCP & Galvanic).
 Conduct the quality inspection for materiel being used and installed on site.
 Proper installation & QC check of conduits, cable pulling, and testing of power/control cables And all
relative electrical works.
Inspection Impressed Current CP Deep Bed Anode Installation.
 CP Test Station Installation inspection.
 Galvanic CP Circuit Potential Testing.
 Inspecting Cathodic Protection System (ICCP & Galvanic) and its components, such as anode installation,
cable installation, and positive and negative cable hookups to rectifier.
 Installation and Testing of Ground Grids for Sub-station.
 Inspection & testing of grounding, grounding pits & bas bar.
 Witness the testing of electrical devices grounding systems, cable Insulation test.
 Monitor the Underground installations; check the required burial depth and spacing requirements to
adjacent installations, prior to backfilling.
 Responsible for complete installation of Grounding and lightning protection system as per the quality
control procedures, approved drawings, specifications and local authorities regulations. Act as a focal point
to the Client.
 Prepare weekly report for progress of works and maintain field records.

Electrical Quality Control Engineer at SEPCO Electric Power Construction Corporation

• Saudi Arabia - Alahsa
• September 2017 to May 2018

Conducting Pre-Inspection and raising Internal RFI for all Construction Activities.
 Responsible for complete Electrical works as per the quality control procedures and approved drawings,
 Specifications and local authorities regulations.
 Inspection for Installation of cable trays, cable ladders etc.
 Attend technical and coordination meetings with the Construction team, and the Client to report on
 Progress and help resolve issues where they arise.
 Making red line Drawings.
 Making Field Clarification Note (FCN).
 Responsible Grounding grid Installation and Testing as per Saudi Aramco Standard & IFC Drawings.
 Responsible cable tray Installation as per NEMA V2.
 Responsible cable testing before cable Pulling.
 Responsible Cable Pulling.
 Monitoring the installation of switch rack and distribution system.
 Monitor the Underground installations; check the required burial depth and spacing requirements to
adjacent installations, prior to backfilling.
 Monitoring on pulling cables through trenches and above ground.
 Ensure work complies with project standards and specifications which involve inspection and checks for
installations of conduits, cable trays, and cable pulling and testing of power and all relative electrical
works.
 Witness the testing of electrical devices grounding systems, cable Insulation test.
 Witness Low voltage cable - Inspection of Cable type and voltage rating, MEGGRING and continuity test on
cable drums. Monitor the Cables laid according to the specification. MEGGERING and continuity to be done
again after laying of cables. Dressing and Splicing of cables, Terminate the core with proper lugs and
overall cable laying and termination.
 Installation and Testing of Ground Grids for Sub-station.
 Monitoring on pulling cables through trenches and above ground.
 Presently involved in solo run ensure to all work done as per standard and specification.
 Issued site instructions and (NCR) for unacceptable work practices at site in co-ordinate with the Head of
Department/Design Staff and obtain their comments prior to auctioning.
 Inspection for Laying and termination of Control and Power cable.
 Responsible for complete installation of pumps as per the quality control procedures and approved
drawings, specifications and local authority’s regulations. Act as a focal point to the Client.
Inspection for MV/LV motor solo run test.
 Inspection for MV/LV motor winding resistance check.
 Attend technical and coordination meetings with the Construction team, and the Client to report on
progress and help resolve issues where they arise.

Electrical Site Engineer at SEPCO Electric Power Construction Corporation

• Saudi Arabia - Riyadh
• January 2016 to July 2017

1-Installation of ACWL, JBs, Panel and wiring in Flare Area.
2- Installation of Cathodic Protection System of Pipelines, Sleeves and Tanks as per Saudi Aramco standards.
3- Installation of Cable tray, ladder, wire mess and conduit, rigid metal etc.
4- Installation of underground and above ground conduits, cable trays, duct banks, power and control system.
5- Installation of Electrical works via cabling, underground/above ground, cable trays, lighting systems indoor/outdoor and lightening protection system etc.
6- Installation and Testing of Ground Grids for Sub-station.
7- Installation Termination of Medium voltage & low Voltage Cables.
8- Installation of Ground Rod and Grounding cable, as per Engineering Drawings.
9- Testing and Laying of direct buried magnesium anode via Cad weld connection and installation of Test stations.
10- Witness insulation resistance test and Continuity test for power cables.
11- Checked and reviewed all the electrical engineering items and equipment.
12- Supervise installation activities at site with regards to proponent specification and standards.
13- Responsible for conducting surveillance and inspection duties for work defended herein and efficient recording and reporting of the result as required
14- Coordinating with site Supervisors for arrangement of materials required in the site.
15- Material receiving electrical equipment, meager test of cable
16- Insulation, continuity of cable.
17- Inspection of Grounding works such as grounding rod installation, cad weld connection, welding of ground connection point
to structures, vessels, and platforms, laying of cables for ground grid and terminations.
18- Issuing construction punch list for the construction department if needed.
19- Cables installation of MEGGRING and continuity to be done again after laying of cables.
20- Follow the response to technical queries from client/consultant including Correspondence.
21- Able to Work & follow Electrical standards like NEC, NFPA, IEEE, NEMA & Saudi ARAMCO standards.

Electrical Engineer at Sapphire Diamond Fabrics Ltd

• Pakistan - Faisalabad
• July 2011 to June 2015

1- Installation & maintenance of Switch gears, Transformers, Motors, Generators and other electrical devices like ATS, Electrical Panel Boards & Bus Bars.
2- Reading control panel diagrams & Troubleshooting.
3- Work on GE Jenbacher JS 320 and control panel.
4- Work on Caterpillar Diesel Generators.
5- Work on Cummins Diesel Generator.
6- HV Cable Termination.
7- Reading Electrical Drawings.
8- Electrical material supply and procurement.
9- Maintenance of engineering equipment or plant.
10- Maintain and service all machinery; including mechanical and electrical aspects.
11- Maintenance engineers undertake scheduled and breakdown.
12- Maintenance of engineering equipment or plant.
13- Planning and scheduling planned and unplanned work.
14- Diagnosing breakdown problems.
15- Arranging specialist procurement of fixtures, fittings or components.
16- Controlling maintenance tools, stores and equipment.