Senior Manager
Energo Engineering Projects Limited
مجموع سنوات الخبرة :18 years, 0 أشهر
1. Turnkey Projects of Thermal Power Sector. Engineering & Construction/EPC/CHP/BOP base work. Material Handling, Utility Systems of Coal/Aluminum Handling Plants, Bulk Material handling, Smelter Plants, RMHS.
2. Working on the Pre-Qualification Requirements as mentioned in the Tenders, Biding, Cost Control and Technical Proposal Works.
3. Preparation of the Commercial Deviations and working on the Price Implications.
4. Preparing various system detail Cost Estimation Sheet for Techno Commercial Offer for Thermal Power Plants/Raw Material Handling/Steel/Aluminum SMELTER Industries.
5. After getting the Order, preparation of the Contract.
6. Selection of suitable Vendors, Vendor Evaluation and preparation of the Vendors Database.
7. Flotation of enquiry, interaction with vendors, reviewing of scope and preparation of technical and commercial
8. Comparison of various vendors after finalization of vendor's scope.
9. Preparation of Transfer Price for Project Management, budgets, project schedules.
10. Monitoring contractual terms and conditions with suppliers and sub vendors.
11. Selection of suitable technologies and vendors.
12. Study of vendor capabilities and their existing customer's base.
13. Finalization of supplier's scope and commercial comparison.
14. Participation and assistance to Top management in commercial negotiations.
15. Executing and supervising erection activities at site.
16. Project monitoring.
1. Mechanical Design experience in Aluminium Smelter Reduction Technology for complete new as well as further improvement of existing technology.
2. Working experience and selection of various mechanical equipment related to reduction pot line.
3. Working experience on various process, operation & maintenance related to reduction pot line.
4. Material handling working experience on smelter green carbon anode plant, rodding shop, fresh alumina handling, butt recycling, crush bath handling, ALF3 /Al2O3 handling etc.
5. Mechanical design experience on dry scrubber & GTC/FTP design.
6. Working knowledge on pot bath chemistry, aluminium production, and overall pot cut out & cut in, pot bath up, preheat etc.
7. Working knowledge on Dense Phase System & Air Slide related to Al2O3 & ALF3 handling system.
8. Actively participating for Floating enquiry for various equipment related to pot line and performing techno commercial negotiations with suppliers too.
9. Conversant with Alumina Pechiney (AP), EIL, Brochot, Rio-Tinto-Alcan etc. Plant Design Technical Specification.
1. I am associating in detail Mechanical Engineering design execution of Mechanical/Utility Systems of Aluminium Smelter Plant, Coal Handling Plants, BOP, Green Anode Plants etc.
2. Independently preparing Design analysis of Aluminium Smelter pot room, Technical Proposal for Bidding/Tender Engineering and detail Cost Estimation & Cost Control and Project Monitoring work for various Plant Auxiliary systems like Ventilation/AC/Dust Suppression/Dust Extraction/DFDS/Cold Fog/Piping/Ducting calculation & design.
3. Various Water Based system like Service Water, Cooling Water, Potable Water, Sump Pump, Feed Water, Compressed Air, HVAC, Tunnel, Ventilation Duct Layout Design.
4. Air Pollution Control design for Plant as per ACGIH regulation. Detail pre calculation and proper selection of approved make Fabric Bag House, Cyclone, ESP, Ventury Scrubber, Baffle Plate etc.
5. Detail design of Fire Protection System for Plant. Detail system design and calculation for Hydrant, MVWS, HVWS, Spay System & Fire Extinguisher, in line with TAC & NFPA standard.
6. Working knowledge in various Material Handling Equipment like Stacker/Reclaimer, Gear Box, Plough/Vibro Feeder, Coupling, Crusher, Coal Sizer, Coal Sampler, Wagon Tippler, Track Hopper, ILMS, Belt Conveyor, Pulley, Idler, EOT crane, Hoist, Chute, Skirt Board, Sprinkler, Water Nozzle, Rain Gun, Air Compressor, Pumps, Industrial Fans etc.,
7. Working in detail calculation and Finalizing of Coal Flow Diagram and Layout Plan.
8. Preparing detail Design Basis Reports (DBR) for various essential systems like,
i. Heat Load Ventilation Calculation at Electrical Switchgear Room.
ii. Air Condition System Calculation at various premises under Plant.
iii. Tunnel/Under Ground Building Ventilation System.
iv. Air Pollution-Dust Suppression & Extraction System.
v. Fire Protection System based on TAC, NFPA guidelines etc.
vi. Plant Water Based Plumbing System like Service/Potable/Cooling/Water Intake/Sump Water system etc.
vii. Various Material Handling - Mechanical Equipment Technical Specification.
9. Conversant of Design Engineering Technical Specification of DCPL, BCCL, BECL, NTPC, MECON, DESIN, Brochot (France), TCE Consulting etc.
10. Familiar working with F.Harley, APC, Dustven, Spray System, Nalco, Mahagenco, Vedanta, Jindal, RITZ, Ingersoll Rand, Atlas Copco, Magnetic Industry, TRF, L&T, Thy-Krup, Elecon, MMD, FL Smidth, Andrew Yule, Kirloskar, Baldor, Flakt India etc.
11. Procurement & technical Vendor evaluation and Vendor finalization of Material Handling equipment like conveyor package, NN/ST belt, pulley, idler, gear box, coupling, rapid loading system, air blaster, coal sampler, belt scale, ILMS, plough feeder, vibro feeder, crusher, coal sizer, air pollution control equipment, hoist, chain pulley block, plummer block, conveyor's safety devices etc.
1. I associated with Static Equipment Design (Vessels, Tanks etc.) by using PV Elite & Code Calc., Detail Engineering Manual Calculation for Static Equipment as per appropriate ASME/API/BS Codes. Detail Engineering/GA drawing part marking, preparation for MTO etc. Co-ordination of all engineering activities, which come under the scope of Mechanical Department.
2. I associated in new product development (R&D Design) of Pressure Vessel, Design of Heat Exchanger, Design of Storage Tank, Design of other Static Equipment by various methods, Preparing Material Take-off, Define Fabrication Codes of Pressure Vessel, Various Excel calculation with related to Pressure Vessel and Pipes etc.
Mechanical Engineering [2 Years Course]
Mechanical Engineering [4 Years Course]
12th Standard (Higher Secondary Examination) including Physics, Chemistry, Mathematics, Biology, English etc.
10th Standard (Secondary Examination) including Physical Science, Mathematics, Biology, English etc.