ENGINEERING TECHNICIAN
Saudi European Petrochemical Company - Ibn Zahr
مجموع سنوات الخبرة :0 years, 0 أشهر
Ensures compliance as per SHEM PROCEDURE STANDARD
Electrical safety procedures, Environmental safety and securities procedures as well as occupational
health and safety procedures.
Observe safety hazards, unsafe conditions, near miss.
Reports to the nominated IBNZAHR Electrical Maintenance Supervisor for day to day work.
Carry out scheduled preventive maintenance of Electrical equipment’s in a safe and secure manner.
Carry out predictive, corrective and shutdown maintenance as assign by supervisor in charge to prevent
failure and enhance reliability and viability of electrical equipment and machinery within assign area.
Identify common failures and make recommendations for corrective actions.
Provides accurate maintenance history and closeout reports of all completed jobs per company
requirements.
Troubleshoot, repair/replace faulty electrical equipment and system.
Conduct daily maintenance activity, troubleshoot, repair, preventive maintenance of
1. UPS System
2. Motors
3. Breakers
4. Battery banks
5. Battery charger
6. Lightings
7. Compressor
8. Generator
9. Provides a support during electrical equipment failure investigation, troubleshooting and
perform high-skilled diagnose.
Performs skilled electrical work of all types in shop or field. May provide work direction to lower class
electricians as required.
1. Inspect electrical equipment to determine the extent if repairs required using test equipment
such as VOLTMETER, AMMETER, OHMMETER, MEGGER.
2. Disassembles electrical equipment, makes wiring diagrams, replace or repair parts such as
switches, control elements, winding test and diagnose malfunctions.
3. Makes repair to motors, check for electrical integrity, undercuts and re assemble electrical
equipment’s. Make proper internal and external connections.
4. Install, maintains and repairs wiring system, set power of lighting boards and panels, motor and
controls. Install fixture, check and test before put in service.
Ensures compliance of all times permit to work procedure.
Witness functional test did by contractor if there is some faulty or inaccurate connection as per
schematic diagram procedure.
Functional test of switchgear or pre commissioning of switch gear to check the condition if that is
perfectly working. Check the selector switch control for OFF, AUTO MODE, LOCAL MODE, and in
PARALLEL FUNCTIONS are working correctly and the time of cutting off the incomer breaker and bus tie
breaker is accurate timing when they encounter under voltage.
Motor protection relay parameter check. Insures that all input parameter is fit to the motor design. And
all functions is working perfectly
Manage the hi pot testing of bus duct, bolt torqueing, continuity resistance megger testing and megger
test of LV and HV bus duct.
Manage the pre commissioning of motors which already installed in site. Check the avaibility of motor if
that is faulty during installation or not. Conduct insulation resistance test of the winding of motor, shaft
performance and bearing check.
Transformer functional test. Check the performance of transformer during test run. Check the rotation
of fan motor if that is correct, Check the settings of all alarms if that is functioning like High WINDING
Alarms and trip, HIGH TEMPERATURE ALARM AND TRIP, BUCKOLS ALARM AND TRIP SEAL IN RAPID
PRESSURE RELAY ALARM AND TRIP.
Ensures all activity should be reported to supervisors for further review and actions
INDUSTRIES: SATORP (SAUDI ARAMCO TOTAL REFINING AND PETROCHEMICAL)
INDUSTRY: SHOAIBA COMBINED CYCLE POWER PLANT
DATE: SEPT. 1,
Ensures compliance of all times with permit to work procedures.
Observe safety hazards, unsafe conditions, and near miss and report to supervisor.
Troubleshoot, repair and replace faulty electrical equipment and system.
Carry out work preventive and corrective maintenance as assign by
Knows and ensures the company and client standards and project procedures
Glanding and terminations of both electrical and instrument equipment
Following the diagram given by the client
Knows how to interpret and read diagrams
Cable tray installation
Commissioning test of electrical device. Follow the test procedure given by the supervisor and client
Visual and mechanical check
Continuity resistance megger test of low and high voltage bus duct
Megger test of low and high voltage cables
Insulation test of both low and high voltage wire
DC HI-POT and rotation test of motor