Nafees خان, Mechanical Incharge

Nafees خان

Mechanical Incharge

Noor Energy 1 , Nomac Gulf CSP

البلد
الإمارات العربية المتحدة - دبي
التعليم
بكالوريوس, Mechanical Engineering
الخبرات
16 years, 0 أشهر

مشاركة سيرتي الذاتية

حظر المستخدم


الخبرة العملية

مجموع سنوات الخبرة :16 years, 0 أشهر

Mechanical Incharge في Noor Energy 1 , Nomac Gulf CSP
  • الإمارات العربية المتحدة - دبي
  • أشغل هذه الوظيفة منذ مايو 2021

Commissioning and troubleshooting of turbine pumps, canned, multistage pumps and other rotary equipment’s ❖ Maintenance & Troubleshooting of Aux. boiler, Piston, screw compressor, blower and others ❖ Execution of PM & CM plan, MEL, ROS checklist, Service contracts, plant lubrication, Condition monitoring, safety critical device. ❖ Support in implementation on S4 Hana SAP system by preparing maintenance plan as per the SAP requirement ❖ Responsible for assisting project manager in entire project management activities for managing the project within stipulated time, adhering to project schedule and budget. ❖ Managed the project as per schedule and planning, monitored the project progress, weekly review and monitoring of man-hours and budget. ❖ Prepared Monthly progress report, minutes of meetings, successfully organized kick-off meeting, and technical meeting with various vendors for Project. Also organized weekly review meeting.

Mechanical Engineer في Shuaibah-3 Expansion II Project – WDEC-ACWA Power
  • المملكة العربية السعودية - أبها
  • مارس 2020 إلى مايو 2021

Major Equipment’s maintenance  Troubleshooting & Modification of system  Maintenance of HPP, Horizontal, Cavity, dossing & ETC pump’s  Vessel membrane replacement, ERD inspection & maintenance  TBS, Sludge pump, Bag filter inspection & maintenance  Managing preventive & corrective of CF, DMF, Service pump, Cleaning & flushing pump  Dosing pump, Screw conveyor, Air compressor ETC  Motor alignment & troubleshooting of high vibration in HPP & Motor  Preparing maintenance budget, Timesheet, Shutdown planning  Preparation & closing of workorders, notification & generation of warranty defects  Preparation of RCA and concussion reports  ETC  Support development and refinement of Equipment Preventive Maintenance Routines, optimization of their schedules, and analysis of their effectiveness.  Review engineering specifications/drawings and propose design modifications to improve reliability within cost and other performance requirements  Analyze and provide technical support to during maintenance, repair, modification, commissioning & testing of machinery  Recommend Modifications to Existing Production Standard Operating Procedures to Achieve Optimum l Quality Within Limits of Equipment Capability

Mechanical Engineer في M/S City Cement Company
  • المملكة العربية السعودية - الرياض
  • مارس 2017 إلى ديسمبر 2019

Major Equipment’s maintenance & replace plant Such as :
-Replacement of cement mill Diaphragm
-Optimization & Erection of Rolling press
-Routine inspection & over hauling of Mill’s drive Gear box with the
co-ordination of service Engineer.
-Major Repair’s & replacement of equipment’s
-ETC
Support development and refinement of Equipment Preventive
Maintenance Routines, optimization of their schedules, and analysis of
their effectiveness.
Review engineering specifications/drawings and propose design
modifications to improve reliability within cost and other performance
requirements
Complete technical projects to gain an understanding of the operations of
a cement plant and the cement industry, as well as gain practical
application of engineering skills.
Analyze and provide technical support to during maintenance, repair,
modification, commissioning & testing of rotating machinery
Projects:
Managing project activity of Alternative fuel Resources (AFR) Project such
as TDS- (Tire derived shreds) used tire chips as an alternate fuel with
HFO in cement industry by using whole tire and OTR tire.
Erection, Installation & commission of Pyrolytic carbon black powder
feeding system to Pre-calciner of kiln Pre-heater
Erection, Installation & commission of SPL (Spent pot lining) feeding
system to Pre-calciner of kiln Pre-heater- First time in Saudi Arabia
where SPL is used as Alternative fuel
Analyzing & preparing various plan with the co-ordination of various
department for establish RDF project- Refuse derived fuel: Produce from
various municipal, Industrial & Commercial wastes (MSW). -Ongoing

Mechanical Engineer في Yanbu Cement Company
  • المملكة العربية السعودية - ينبع
  • يناير 2010 إلى ديسمبر 2016

Managing overall activities of:
Kiln & Oil Station: Kiln capacity of 10, 000 TPD (Día 5.4X82m long) - KHD
Air Swept Raw mill of capacity 325 TPHx2 (In line- 4 of capacity 8200
TPD)
Crushers
Power Plant -165 MW
 Maintaining, operating, and repairing a variety of equipment
including:
Installation, alignment and commissioning of bulk material conveying
equipment’s such as Belt conveyors, Screw conveyors, Air slides,
Elevators and deep pan conveyor etc.
Alignment and commissioning of Pollution control equipment’s like Bag
filters, Electrostatic precipitator & Reverse Air Bag House.
Various conveyor system, Auxiliary, Pumps, centrifugal fans, and
blowers
Assist in developing, recommending and managing process & equipment
reliability programs (Root cause failure analysis/ Mean Time Between
Failure)
Material handling equipment like belt conveyors, pan conveyors, bucket
elevators, and many other
Stationary equipment like Clinker Cooler with capacity 8500 TPD, grate
cooler makes and capacity 4000 TPD, grate cooler makes
Air compressors & blowers, cooling tower & high-pressure water pumps
Boiler/Thermal Heater, Ring/Screw, HFO & HTO pumps
Conducting all maintenance activities such as attending breakdowns,
conducting Route Cause Analysis, Why-Why Analysis, Trip Analysis to
find out root cause of breakdown, implementing corrective/ preventive
actions
Replacing HP & LP pumps, apron feeder spares, weigh feeder, conveyor
belts, re-claimer & side scrapper maintenance jobs.
Implementing Kaizen for ensuring for zero breakdown, spare cost & cycle
time reduction; insulating pipelines of all equipment
Ensuring availability & delivery of right quality materials/parts at the right
time, price & terms; coordinating with Planning, Projects & Quality
Teams and Stores for effective inventory control

Mechanical Engineer في A.C.C Cement Company
  • الهند - اندور
  • يناير 2008 إلى ديسمبر 2009

Maintained daily, weekly & monthly activity of PMS, Inventory & Purchase related to maintenance and production
Looking after all the maintenance of machinery belong to Raw mill & cement mill such as reclaimer, stacker,
separator, cyclones, belt conveyors ETC
Maintenance of Mills liners, diaphragms, lubrication pumps, Elevators ETC.
Maintenance of Transporting system equipments such as belt conveyors, pan conveyors, weighing feeders ETC.
Conducting all maintenance activities such as attending breakdowns, conducting RCA, Why-Why Analysis to find
out the cause of breakdown, implemented corrective/preventive actions.

الخلفية التعليمية

بكالوريوس, Mechanical Engineering
  • في BITS,BHOAL
  • فبراير 2008

Mechanical Engineering Modified Material Conveyor system

Specialties & Skills

Budgeting
Planning
Troubleshooting
Mechanical Maintenance
AUDO CADD
Mechanical Engineer,Service/Maintenance Engnr,Maintenance Operations,Mechanical Engineer
,Predictive Maintenance,Preventive Maintenance
Root Cause Analysis,Project Planning,SAP
Production Mgmt,Commissioning,Erection,Breakdown Maintenance,
Maintenance,Project management

اللغات

الانجليزية
متمرّس
العربية
متوسط

العضويات

Saudi Council Of Engineering
  • Mechanical Engineering
  • February 2013

التدريب و الشهادات

PMP-Project Management Professional (تدريب)
معهد التدريب:
PMP
تاريخ الدورة:
December 2017
المدة:
35 ساعة
Internal Auditor (تدريب)
معهد التدريب:
TUV Nord
تاريخ الدورة:
October 2012
المدة:
48 ساعة
IMS & OHSAH (تدريب)
معهد التدريب:
TUV Nord
تاريخ الدورة:
April 2017
المدة:
62 ساعة
ISO AUDITOR (الشهادة)
تاريخ الدورة:
February 2014
صالحة لغاية:
January 9999

الهوايات

  • All Games