Electrical Technician
Airbus Defence and Space
Total des années d'expérience :18 years, 10 Mois
1- Assembling & Installation of Electrical equipment in Electrical panels, DB and rack monitoring systems.
2- Splicing, crimping & termination of electrical Power, Control, & Data cable as per drawing/standard color coding.
3- Trouble-shooting, tracing, diagnosing and rectifying electrical faults in SCADA wiring & control / power circuit…
4- Performed corrective maintenance, Preventive maintenance and break-down job on electrical equipments.
5- Installation of VFD, PLC/SCADA system & wiring of input, output & power module at SCADA & equipment side.
6- Installation of MCB, MCCB, RCBO, SPD, control relay, magnetic contactor, control & power wiring & cable termination as per standard color coding/approved drawing, and performed tagging /labeling...
7- Installation of industrial computer/server, RPDU, LCD, LAN switch & Hum. / Temp. sensor.
8- Installations of three phase UPS, batteries, power cable termination of UPS & non-UPS power supply and TERMA Scanter 5200 for Maritime Radar antenna system.
9- Using of hand tools, power tools, multimeter, clamp meter, insulation tester, earth tester.
10- Testing of Electrical equipment, Electric panels, monitoring rack for wiring insulation test, earthing test, earth leakage test, Voltage/Amp test, & fill the test format.
11- Modification job as per site requirements & prepared Red-line/Mark-up drawing for final as-built copy.
12- Performed RFI testing in front of witness / consultant, as per approved check list/documents...
13- Documentation work like maintaining record, daily progress report, material request, BOQ, etc…
14- Reading of Electrical schematic control & power drawing, wiring diagram, Ladder logic & termination schedules.
15- Acknowledge & follow the company safety and security policies and procedures...
1- installation & maintenance of power & control equipments/devices, hardware in electric panel.
2- Installation of three phase induction motor, VFD drive.
3- Tracing, Diagnosing and rectifying electrical faults in control & power circuit.
5- Installation of MCB, RCCB, SPD, DLSPB, Control Relay, Magnetic Contactor, control & power wiring / cable termination as per color coding & approved
1- installation & maintenance of power, control & communication equipments/devices, hardware in electric panel / equipment .
2-Tracing, Diagnosing and rectifying electrical faults in control & power circuit.
3-Power, Control, Grounding & Data cable splicing, crimping & termination as per drawing/standard color coding.
4- Installation of three phase induction motor, servo motor servo drive, VFD drive, PLC system & wiring of input, output & power module/card ...
5- Installation of MCB, RCCB, SPD, DLSPB, Control Relay, Magnetic Contactor, control & power wiring / cable termination as per color coding & approved
1- Assembling & Installation of Electrical equipment in Electrical panels, DB and rack monitoring systems.
2- Splicing, crimping & termination of electrical Power, Control, & Data cable as per drawing/standard color coding.
3- Trouble-shooting, tracing, diagnosing and rectifying electrical faults in SCADA wiring & control / power circuit…
4- Performed corrective maintenance, Preventive maintenance and break-down job on electrical equipments.
5- Installation of VFD, PLC/SCADA system & wiring of input, output & power module at SCADA & equipment side.
6- Installation of MCB, MCCB, RCBO, SPD, control relay, magnetic contactor, control & power wiring & cable termination as per standard color coding/approved drawing, and performed tagging /labeling
7- Installation of industrial computer/server, RPDU, LCD, LAN switch & Hum. / Temp. sensor.
8- Installations of three phase UPS, batteries, power cable termination of UPS & non-UPS power supply and TERMA Scanter 5200 for Maritime Radar antenna system.
9- Installation of induction & servo-motor, servo drive, encoder, motion sensor, limit switch & solenoid coil.
10- Installation and maintenance of 1 Phase 220V & 3 Phase (380-400V) motor with different starting methods.
11- Using of hand tools, power tools, multimeter, clamp meter, insulation tester, earth tester.
12- Testing of Electrical equipment, Electric panels, monitoring rack for wiring insulation test, earthing test, earth leakage test, Voltage/Amp test, & fill the test format.
13- Modification job as per site requirements & prepared Red-line/Mark-up drawing for final as-built copy.
14- Performed RFI testing in front of witness / consultant, as per approved check list/documents.
15- Documentation work like maintaining record, daily progress report, material request, BOQ, etc…
16- Reading of Electrical schematic control & power drawing, wiring diagram, Ladder logic & termination schedules.
17- Acknowledge & follow the company safety and security policies and procedures...
1-Performed Installation, Corrective Maintenance, and Troubleshooting of 380kV GIS LCC Panels, Control Panels, Protection Panels, LV AC/DC Aux. Supply Panels, Fault Recorder, Annunciator Panels, Busbar Protection, PD Panels, Breaker failure Protection Panels, Line Protection, Ethernet Switch panels, & Communication Panels…
2-Performed Installation, Corrective Maintenance, and Troubleshooting of 115kV GIS LCC Panels, Control Panels, Protection Panels, SCADA/SAS System Panels, & 67MVA Power Transformer Control/MK Panel…
3-Performed Installation, Corrective Maintenance, and Troubleshooting of 13.8kV Switchgear & Cap. Bank…
4-Modification work on Electrical Control/Power Panels, Protection Panels & LV AC/DC Power distribution system
5-Installation of PLC/Programmable Logic Control, VFD, IED/Numerical Relay, SAS/SCADA system, & CT / VT…
6- induction electric motor, servo motors, encoder, cable termination, motor control & power panel with different starting method
7-Power, Control, Grounding & Data cable splicing, crimping & termination as per drawing/standard color coding.
8-Installation & troubleshooting on magnetic contactor, magnetic relay, time relay, phase sequence relay, MCB, MCCB, ELCB/RCCB, Selector Switch, change-over switch, Over current relay & Under Voltage Relay, of different manufacturer, ABB, SIEMENS, GE, Schneider, Alstom, SEL, Finder,
9-Maintenance of chiller, PACU Units, EDH, / HVAC System/DDC panel of substation & industrial plant …
10-Domestic, Commercial and Industrial Power Distribution system and load balancing…
11-Using test equipment, mult meter, clump meter, cable detector, LV & MV insulation test (100-5000V), contact resistance, hand tools power tools, and labeling/ferruling machine….
12-Cable laying on cable tray, cable glanding & control cable termination works as per cable termination schedule.
13- Install & maintain many kinds of indoor/outdoor AC & DC lighting distribution panel, & automatic LP-OD.
14- Well capacity to read electrical control scheme drawing, power scheme drawing & wiring diagram, lighting drawing, cable termination schedule & equipment layout plan drawing, updating of drawing/Red markup as per requirements of site changing/modification…
15-Prepare material estimation & BOQ of assign job & prepare purchase request, daily progress report on computer
16- Inspect electrical systems, equipment, and components to identify hazards, defects, and the need for correction Acknowledge & follow the company safety and security policies and procedures.
maintaining, and repairing electrical equipment control panel & power
panel, chiller, chilled water pump, domestic water pump, power cable termination and
overhauling up-to 5kW motor, Circuit breaker magnetic contactor,
* Conducted daily routine inspection of overall altogether plant/equipment
* Performed preventive maintenance day by day as per master schedule
* Conducted troubleshooting for in control/power circuit, fixing the faults.
* Responsible for all electrical and day-to-day tasks relating to maintenance. regularly
* install commercial and industrial lighting systems of various sizes and styles
* Troubleshot and installed various ballasts, lighting contactors, etc. Troubleshoot and repair
major and minor electrical systems, including motor operated valves, ground isolations in
load centers, air conditioning and refrigeration plants, power and lighting distribution
circuits
Responsible for installing, maintaining, and repairing electrical equipment
like control panel & power panel, switchgear, transformer, electric motor power cable
termination and overhauling up-to 5kW, VFD, PLC, relay, Circuit breaker, magnetic
contactor, aux. relay, over current relay & isolator/safety switch….
* Conducted daily routine inspection of overall plant/equipment
* Performed preventive maintenance day by day as per master schedule to avoid any sudden
failure /shut down…
* Conducted troubleshooting for rectify any fault in control/power circuit & diagnosing, fixing
and locating electrical faults using hand tools and test equipment.
* Undertaking electrical installation and routine maintenance work.
* Electric motor termination, motor control & power panel with different starting method
* Keeping all the paperwork properly up-to-date…
* Responsible for all electrical and day-to-day tasks relating to maintenance. regularly
* Ensuring that all work done is in compliance with health & safety regulations...
Diploma in Electrical Engineering
