Structural Engineer
Etec Bahrain
Total des années d'expérience :21 years, 9 Mois
• Report to Project Director/Resident Engineer ADPi and General Manager ETEC. Review Structural Shop Drawings, Document Submittals, Structural Design Calculation Reports, Material Submittals, Site Clarification Requests, Inspection Requests & various Submittals as per the Project Document Control System. Provide alternative Structural Design solutions for modifications arising on Client’s request. Codes used ASCE7, ACI318, IBC2009, BS EN codes.
• Technical Coordination with Contractors Arabtec-TAV Joint Venture, GPZ, AMA and with other trades & disciplines.
• Clarify technical queries arising from Client ‘BAC’, PMC ‘Hill International’ and the QS ‘AECOM’
Report to General Manager. Responsible for Structural Design and Drawings control, Technical Management & Coordination of Structural, HVAC & MEP, Project Management involving Manpower & Materials complying with Project Specification & BOQ, Technical Review & Coordination for Elevators, Cone Shade, Shutter Doors, Cladding fixture, Air Conditioning & HVAC etc, Supervise, Monitor and Manage the sub-contractors, including their compliance with their contracts, preparation of construction management plans, safety and security of the works, progress, quality, environmental aspects etc. BS6339, BS8110, BS8004, BS5950 codes
• Report to Project Manager. Review Design Calculations & Contractor’s Drawings, Inspections for Structural Works-RFIs, Prevention Action Reports and Non-Conformance Reports x site Inspection.
• Provide Tender Drawings, Technical Specification and Scope of Works for various Plant Works & Industrial Buildings in Concrete & Steel Structures.
• Assess EPC Contractors’ Work Plan, Review Construction Documents, Provide Technical Support; Coordinate for Project implementation with other disciplines, Plant Operations Departments etc.
• Clarify Technical Queries via Technical Meetings and Weekly Progress Meetings, etc.
• SAP-PS, PM Module: Project Implementation via SAP PS & Maintenance via SAP PM Module.
• MDRM: Develop Master Data for the Plant & Projects through Pilog system, MDRM.
Skills & Achievements: Achieved substantial saving (cost & time) for the client by proposing 33kV Cables Routing from Deep Tunnels of Steel Plant to Shallow Cable Basement of the 33kV GIS Substation Building with feasibility of Structural Design. This eliminated redesign of the 33kV Substation with Deeper Basement.
• Report to Chartered Structural Engineer (MIStructE).
• Front End Engineering Design (FEED), Perform Structural Analysis & Design Calculations based on BS Codes, Standards & Specifications, Structural Design in StaadPRO, ETABS, PROKON etc., Lead team of Cad Operators in the preparation of Tender & Construction Drawings, Review Calculations for Precast Hollow Core Slabs, Precast Boundary Walls, Precast Foundations, Pile Designs, Steel Portal Frames and Hybrid Structure Design.
• Attend Technical Meetings with Clients, Electrical Consultants, Clarify Technical Queries, Propose Preliminary Design Schemes and Structural Options to clients.
• Approval of Shop Drawings, clarify structural related RFIs raised by contractors.
Skills & Achievements:
• Achieved substantial saving (cost & time) for the client by eliminating Ground Improvement by Stone Column after reviewing the Soil Reports and Plant loads for Awalco AC Assembling Factory set in 120mX280m area Steel Portal Frame Structure.
• Excellent 3D Modeling in (Finite Element) StaadPro (including interface with AutoCAD), Etabs, AutoCAD etc. Excellent hand calculations on Excel Spreadsheets. Excellent interface between CAD software and Analysis & Design Software. Have designed Excel programs for Pre-Tensioned Hollow Core Slabs, Retaining Walls and Pile Caps etc. Have worked designs based on IS Codes, BS Codes, ACI and UBC.
• Key role from Schematic Design to complete Construction Documentation 35 numbers of 220kV/66kV GIS Substations in Bahrain, Arabian Sugar Refinery, Awalco Factory, Iconic Structure like Sail Monument in Bahrain.
Dynamic Analysis of Steam Turbine Generator Foundation for BAPCO, Bahrain:
The Steam Turbine Generator has a Generator, Gear Box and Turbines. These units are installed on 14.5mX6.9mX1.6m deep Raft foundation. The foundation is reviewed for Free Vibration Analysis to check the frequency of foundation to be maintained at +/-20% away from the equipment frequency and also reviewed for Forced Vibration Analysis to check the amplitudes of the foundation due to dynamic loads not to exceed the allowable limits as specified by the equipment vendor.
220kV/66kV Substations:
More than 35 numbers of 220kV/66kV BSP, City & Loop Type substations all over the country of Bahrain were proposed by Ministry of Electricity & Water Authority. These substations have 220kV GIS Bldg., 66kV & 11kV Switchgear Bldg., 150MVA & 66kV Transformers and 220kV & 21kV Reactors, NER, NES, Battery Room, Control Room, Capacitor Banks, House Transformers etc. The buildings are 8m to 12m high single storey building with 5T Crane Girders and the roof has max of 320thk Precast Hollow Core slabs spanning for13m. There are free standing walls up to 9.0m high. The building is supported on a 450mm thick Raft Slab. Some of the large substations are Addur, Tilal A’ Ali, Diyar Al Muharrak, Dahiyat Al Seef, Shamal Al Fateh etc.
AIRCRAFT HANGAR & facilities Building at Bahrain International Airport, Bahrain:
An Aircraft Hangar of size 80x45x22m is proposed at BIA for which the Steel Roof at entrance is considered to having a Double Truss spaced 2m apart spanning 80m. Use of 355grade as per BS5950 specifications was considered. Wind Calculations based on BS6399: Part 2 for open sided buildings indicated horizontal net pressure of 1.3kPa and an upward net pressure of 2.3kPa. These were modeled in StaadPro software and verified by hand calculations and sections were optimized.
Sail Monument in Steel:
The Sail Monument is a double curvature right-angled triangular structure 15m high x15m breadth cladded with Fiber Glass Reinforced Plastic(FGRP) and this is analyzed as a cantilever steel structure against wind pressure in StaadPro software using prismatic members and designed manually as per BS5950 using 15mm thick plates with welded Flanges wherever necessary (making up a built-up section).
Structural Design using Excel Spread Sheets, Staadpro etc. for Residential, Commercial and Industrial Structures. Complete Drawing Documentation for Tender and Construction Stages of various Projects consisting of villas, hotel apartments, malls, industrial factories, substations etc.
Marina Retail Mall @ Amwaj Islands, Bahrain:
Marina Retail is a development in Amwaj Islands. It has a 2 -Storey (with Basement) Retail Structure and a 15 -Storey Apartment Hotel with 210 apartment rooms from levels 2-13. Marina Retail mall includes a multi level car parking, Kiosks, Anchors, Cinema multiplex, Food Court, F&B etc.
Riffa Views, Bahrain:
Riffa Views set in 2.6million square meters with over 1000 villas is a luxury development which includes an international school, Country Clubs, Restaurants, Cafes, Mosques, Spa, State of the art fitness centre and many other sports, entertainment and social activities.
Souk Al Arabia, Bahrain:
Souk Al Arabia set in 46000sqm has a salable and service apartments, Retail areas and Food Courts with swimming pools and landscaped areas. In all, the project features four 12-storeyed towers and one 16-storey tower sharing a two storey podium with retails in Plot A and one 2-storey staff accommodations and community halls in Plot B.
Structural Design using Excel Spread Sheets, Staadpro etc. for Residential Hostel Buildings and 90m high Water Tower Structure. Preparation of Shop Drawings during Construction Stage.
Structural Design using Excel Spread Sheets, Staadpro etc. for Residential, Commercial and Industrial Structures. Complete Drawing Documentation for Tender and Construction Stages of various Projects consisting of villas, hotel apartments, malls, industrial factories, substations etc.
2 years Course includes 1 year project work experience in Structural Engineering.
Quantity Surveying & Site Supervision for commercial complex construction.
Scholarship from the Institution for 2 year study of Master's course at IIT.
Le lien a été supprimé pour non-respect des conditions d'utilisation. Veuillez contacter l’équipe d'assistance pour plus d'informations.