Quality Control Inspector (Pipnig)
Arabian Bemco Contracting Company Ltd
Total years of experience :16 years, 5 Months
• Interface and coordinate work activities between quality and other disciplines.
• Review welding consumables and electrodes for WPS according to ASME Section II Part C
• Prepare monthly reports and statistics.
• Supervise the all site activities.
• Organize internal training programs
• Check the fabrication of piping & structure as per Drawing.
• Make sure the material had the project approval.
• Assisted in resolving all plumbing installation complaints and prepared records of all its findings.
Schedule the inspections for the plumbing systems and ensured that there are no violation.
Ability to enforce the various plumbing codes while inspecting the system.
Inspection of plumbing fixtures handling, storage and preservation.
Inspection of Plumbing fixtures supply piping and drainage piping.
Implement project construction and quality procedures.
Inspect the FRP, GRP, RTR, and GRE U/G and above ground pipes.
Test package review and approval.
Inspection on ducting, lining, insulation of the air‐conditioning lines/system.
Inspection of rotary equipment’s (pumps, motors, generators).
Inspection of static equipment’s (HRSG’S, vertical dumpers, stacks, transition ducts, diverter dumper).
Material receiving inspection.
Hydro test / Pneumatic test Inspection.
Inspect and approve welding of spools according to isometric drawings by checking diameter, thickness, drawing number, and class in welding summary report.
specification and installation procedure and material storage procedure is properly implemented.
Inspection of painting and sand blasting.
Perform/ monitor NDT inspection activities, assess/ review NDT inspection data, RT films and reports
Review welding consumables and electrodes for WPS according to ASME Section II Part C
Mechanical installation of HRSG’s (Module to Module welding, Inlet duct, Outlet duct), HP, LP, IP Drum condensate Tank, transition duct and steel structure.
Installation of pumps, soot blowers, STG’s, generators, ACC’s & its alignment.
Check, verify and review installation of gaskets supports, check valves internals flow orifice strainers instruments and control valves prior to line re-instalment as per the latest drawings for construction.
Line Check Inspection
Accomplishments:
Successfully completed; Large and small bore piping erection for 8 HRSG units \[ Fit-ups & weld visual for approx.1500 joints\], HRSG Outlet duct/ Diffuser and support structure erection for 32 units, Diverter system erection and Installation for 10 units, Installation and verification of piping, stack and HRSG modules.
Discipline Mechanical engineer for punch list and close out of warranty claims with multifaceted responsibilities including but not limited to;
Monitor and Inspect sub-contractors scope of mechanical activities for the closure of punch list items
Assist construction in Itemization of punch points for closure according to description of work and manpower requirements, in addition to the preparation of punch point basket for major remaining works
Conduct inspection with client/ consultant for the closure of punch points & remaining works in lieu of schedule and deadline
Report periodically to Senior Discipline Engineer on Quality& Punch list issues and keep site management informed of any problems
Respond to Technical Queries from Site for Installation & Commissioning and after Start-up & Handover
• Inspect the activities as per Approved QIPs & project specification.
• Generation of punch list.
• To check the fit up and welding as per process piping B-31.3
• Inspect the all erection of structure, pressure vessel, heat exchanger, boiler, columns, and pipe racks.
Erection & Fit-Up inspection of piping and fitting as per approved drawing (CS, SS & Alloys).
Visual Inspection of Welding piping joints (CS, SS & Alloys).
Inspection of underground & above ground RTR & FRP/GRP piping.
Review and witness of MTC, materials and calibration certificates.
Worked in Quality department during the project run and was responsible for NDT (MPI, DPT, UT Thickness Measurement, and Hardness Testing & Hydro Testing), Sand blasting & Painting & Insulation.
To Maintain Record for Steel Structure & Piping work.
Inspection of erection of steel structure as per drawing.
Check the fit up inspection of steel structure.
To prepare request before client inspection.
Holiday Testing and coating inspections
Lowering and backfilling
Test Pack preparations and submission
Weld maps preparation and Control
Preparation of As-Built drawings as per site requirement.
Document Controlling (Piping & Structure)
Mechanical Engineering
mechanical