محمد خان

Project Names: - Construction of 132kv/13.8kv S/S at Tabuk (Year 2016 to till contd.)
Cost & Nature of the project: 103, 339, 223.36 Saudi Riyal (LumpsumTurnKey LSTK)
Job Responsibilities:
• Responsible for the supervision and construction of overall civil works of the project
including construction of 132 kV GIS Hall (Gas Insulated system), 13.8kv SwitchgearHall
and basement, Control room, battery room Foundation of Power Transformer, Auxiliary
transformer including construction of power duct bank, cable Trench and Manhole,
foundation of capacitor and Asphalt roads and construction of precast Boundary wall,
construction and supervision of plumbing and drainage system of the project.
• Prepare and review the shop drawing and as built drawing.
• Organize and conduct the physical and chemical test such as (FDT, sieve analysis, slump
cone and temperature etc.) through independent laboratory for material used in construction
like soil, steel and concrete etc.
• Conduct monthly and weekly meeting with main contractor and subcontractor to track the
progress of work.
• Review technical submittals for the approval.
• Making DPR and RFI’s or RMI’s for ongoing project activities, reporting to the project
manager on monthly basis.
• Tracking the work progress percentage through overall time schedule try to implement
measures at site if there found any delay.
• Supervise and monitor the cleanliness of the site through housekeeping and implement the
safety regulations to prevent any accident happen at site.

Project Names: Interconnection of 132kv s/s to 380kv s/s BSP at Tabuk (Year 2015 to till contd.)
Cost & Nature of the project: 175 million Saudi Riyal (LSTK)
• U/G Cable for single circuit 1200 mm^2 core for Tabuk-11 s/s to Tabuk-9 s/s 3.0km
length approx in 6 sections of 500 meters.
• U/G Cable for single circuit 1200 mm^2 core from 6A to 5B s/s, 850 m. approx. in 3
sections.
• U/G Cable for single circuit 1200mm ^2 core from 6A to Univ. s/s, 850 m. approx. in
3 sections.
• U/G Cable for single circuit 1200mm ^2 core from Univ. s/s to 132kv Gantry 3.25
km. approx. in 6 sections.
• U/G Cable for double circuit 2000mm^2 from 132kv Gantry To 380kv s/s for length
400meters approx. in 1 section.
• Constructions of 132kv OHTL double circuit for approx. length around 17.8km from
BSP 380kv to University Gantry.
• Constructions of 132kv OHTL double circuit for approx. length around 23.4km from
BSP 380kv to substation-11 Gantry.
Job Responsibilities:
• Responsible for the supervision of overall civil works including the construction of U/G
cable trench 1.2m wide and 1.80m depth for laying single circuit power cable of 1200mm ^2
core dia. over sand bedding of thermal resistivity around 300mm thk. After laying the cable
overlaid 1.2 m thermal sand followed by protective tiles and geo grid mesh and warning
tapes before laying sub base. Finally after sub base lay, the material is compacted to 95%
•
where is asphalt road is laid. Precast Manhole installation is needed to be done at every
corner or bend comes during the route for the cable laying process.
• Responsible for the construction of cable joint bay where ever jointing of cable is needed.
• Responsible for the construction of 132 kv Overhead Transmission line including the
construction of 132kv Gantry and its support structure like construction of Surge Arrestor
(SA) & Cable sealing End (CSE) etc. For the above project said as per design the Auger
foundation or pier foundation for tower substructure construction is followed having the
Dia. range varies from 1.0m to 1.6 m for Small angle (SA), Medium Angle (MA) to Heavy
Angle (HA). Depth of Auger foundation varies from minimum 10.0m to maximum 12.0m.
• Responsible for the construction of 132kv Gantry including construction of support structure
likes CSE and SA. As per design the construction comprises as Pad and Chimney for support
structure. Conduct inspection for layout of the structure including and other sub activities
inspection like steel inspection and shuttering as proceed in later stage.
• Responsible for concrete protection with Epoxy an emulsion of bituminous material which
will be done all over the structure as protection layer for concrete.
• At the final stage of the construction, backfill the structure to the excavated area with the
approved fill in layer by layer as of 300mm thick and get ensured the compaction percentage
as of 90% for unpaved asphalt areas and for above 95% for Asphalt paved areas.
Client

Year 2011 to 2015.)
Cost & Nature of the project: 105million Saudi Riyal as Lumpsum (LSTK) for each.
Project Names:
• Construction of Substation Building 132/13.8 KV S/S for Tabouk-10.
• Construction of 132kv/13.8kv S/S at Duba and Albida.
• Construction of Double circuit of 132 kv OHTL (AAAC 500 mm ^2 conductor )from Duba power
plant to 132 kv Duba s/s for approx. distance 32.7km and for U/G cable of 2000 mm ^2 XLPE,
approx. length 17 km till the termination point at GIS basement.
• Construction of Double circuit of 132 kv OHTL (AAAC 500 mm ^2 conductor )from 132 kv Bida
substation to 132 kv MEDYAN (Aramco) S/S for approx. distance 36.7km and for U/G cable of
2000 mm ^2 XLPE, approx. length 2.0 km till the termination point at GIS basement.
Job Responsibilities:
To be noted:
a) Project Responsibilities is same as mentioned above for the Substations.
b) Project Responsibilities is same as mentioned above for the construction
of 132 kv OHTL and U/G Power cable.
Client: Ministry of

Construction of Special Training Area and Task Force (STF) at Half Moon Beach.
Job Responsibilities:
• Construction and supervision of Dormitories, Recreational Halls, Mosque, Kitchen etc.
• Responsible for the construction and supervision of layout of the structure till the finish of the
structure including stages from reinforcement to concreting, plastering to painting of the
structure.
• Responsible for the installation of plumbing and drainage system of the building.
• Responsible for the laying of asphalt road etc.
• Responsible for the installation of sewer pipe lines and installation of cast iron manhole.
• Responsible for the installation of Doors and windows of the buildings.
• Coordinate third party for backfilling material and its compaction as per project specs.
Client

P&C) Procurement & Construction of the Infrastructure for Labor
Camp and gas pipe line corridor. Industrial Area, Jubail.
Job Responsibilities:
• Construction, supervision and Execution for the Infrastructure of labour camp and gas pipe line
corridor which includes the two in nos. of potable water tank of approx dia. 20m and two in
nos. of non potable water tank of approx dia. of 10m with two pump houses.
• Simultaneously the construction of the reinforcement concrete pipe rack has been made of
10.0m to 12.0m of length with section thickness approx 40cm to 50 cm thick for future gas
pipe line.
• Responsible for the overall civil works from excavation till the finishing of the project which
includes the structure layout of the building, supervision and Execution of Block work,
plastering of 20mm thick interior and exterior, painting and installation of doors and windows
and gates for the pump houses with Fire rating of 15hour.
• Responsible for the drainage and plumbing system for the building etc.
Client

Infrastructure Development of Jalmudah Shoreline phase-1
Project Highlights:
The shoreline zone is approximately 6.50 kilometer long and the width varies from 50 m
to over 500 m. The scope of work includes site preparation, earthwork, grading and storm
drainage, roadway including pavement markings and traffic signs, pedestrian paths, sanitary
wastewater system, potable and fire water distribution, irrigation system, landscaping works,
electrical power distribution, street lighting system, landscaping works, telecommunication and
IPTV network.
Job Responsibilities:
• Responsible for the implementation of Quality control procedure on the ongoing project
activities.
• Responsible for the implementing the quality control Organization chart.
• Follow up inspection with the site engineer prior to follow up with the client engineer.
• Prepare the format of civil activities for the Hold point release in M.S.Word
• Follow up with the sub contractor in order to arrange the proper document for the equipment
they use for example calibration certificate, product certification etc.
• Responsible for the preparation of engineering technical submittals / technical queries as per
the Royal commission standards.
• Maintain document control for records, prepare method of statement for the technical
submittals.
• Responsible for verifying the documents for the submittals of vendor/supplier approval.
• Inspect the ongoing activities on site as per the approved drawings or drawings issued for the
construction
Client

Development of township in 101 acre of land
• Responsible for project supervision and implementation of civil work including Building work,
Road work, development of sports club like swimming pool, Gymnasium club etc.
• Responsible for making the Bar bending schedule, work out the BOQ as per the nature of Job
requirement.
• Responsible for carrying out the Layout of columns and footings of a building.
• Responsible for execution of site.
• Responsible for carry out inspection for structural members with approved drawings.
• Responsible for project supervision and implementation of civil work
• Responsible for making the Bar bending schedule as per approved drawings.
• Responsible for checking Lay out of a building.
• Responsible for carrying out inspection for ongoing activities for reinforcement or for shuttering
before casting any structure.
• Responsible for checking slump and temperature test for concrete at time of pouring.
• Responsible and Coordinate meeting with supervisor, engineers for progress.
• Responsible for calculating quantities as per B.O.Q.
• Follow up with the senior engineer for approvals of technical submittals.
• Responsible for conducting meetings with foreman’s and lead man for progress of work.
• Prepare and reviewed of shop drawing.
• Responsible for carrying out inspection for forms work, checking out the levels of formworks
before casting any structure.
• Responsible for carrying out tests on Building material like sieve analysis for fine aggregates
(sand), Coarse aggregate (stones) size 20mm-25mm, slump test for ready mix concrete and
compression and tension test for Bricks used for masonry work etc in order to inspect the quality
of the material.
• Prepare and review the Shop Drawings and as Built Drawings with AutoCAD.
• Discussion with Foreman and junior Engineer to improve the pace and quality of work.

• Responsible for project supervision and implementation of civil work including Building work, Road work, development of sports club like swimming pool, Gymnasium club etc.
• Responsible for making the Bar bending schedule, work out the BOQ as per the nature of Job requirement.
• Responsible for carrying out the Layout of columns and footings of a building.
• Responsible for execution of site.
• Responsible for carry out inspection for structural members with approved drawings.
• Responsible for project supervision and implementation of civil work
• Responsible for making the Bar bending schedule as per approved drawings.
• Responsible for checking Lay out of a building.
• Responsible for carrying out inspection for ongoing activities for reinforcement or for shuttering before casting any structure.
• Responsible for checking slump and temperature test for concrete at time of pouring.
• Responsible and Coordinate meeting with supervisor, engineers for progress.
• Responsible for calculating quantities as per B.O.Q.
• Follow up with the senior engineer for approvals of technical submittals.
• Responsible for conducting meetings with foreman’s and lead man for progress of work.
• Prepare and reviewed of shop drawing.
• Responsible for carrying out inspection for forms work, checking out the levels of formworks before casting any structure.
• Responsible for carrying out tests on Building material like sieve analysis for fine aggregates (sand), Coarse aggregate (stones) size 20mm-25mm, slump test for ready mix concrete and compression and tension test for Bricks used for masonry work etc in order to inspect the quality of the material.
• Prepare and review the Shop Drawings and as Built Drawings with AutoCAD.
• Discussion with Foreman and junior Engineer to improve the pace and quality of work.