Electrical Senior Technician
GDFSUEZ, HUBPOWER PLANT
Total years of experience :4 years, 10 Months
➢ Testing, routine maintenance and troubleshooting of protections relays and Circuit breakers of 6.6kv/6.3KV, buses, also commissioning, and testing.
➢ Overhaul, preventive, corrective and routine maintenance of HV/MV motors up to 5MW, 6.6Kv.
test equipment’s primary current injection test set, FREJA300, SVERKER 750 secondary current injection test set and relay test set, Circuit breaker analyzer, Digital Low Resistance Ohm meter, analog & digital megger up to 5000v, use of AVO meter and DOBLE M4000 multi-function test set, Earth resistance tester, phase rotation check and sequence meter,
➢ Good experience about transformer oil treatment, filling and testing.
➢ Sizing, panel design, ordering and installation of Power factor panel and configuration of the power factor relay by ENTS, Nokian Capacitors and MG,
➢ Installation of SKOV and Blue Earth climate controller and made panel for the MCC and data networking of controllers with infomatic web link.
➢ Well knowledge about HT/LT cable sizing, laying, jointing, and termination.
➢ Also preparing and maintaining equipment history card, call up card.
➢ Maintenance, installation and testing of the cathodic protection.
➢ SF^6 Gas filling, density monitors in GIS. Involved in trouble shooting GIS.
➢ Electrical protection relay testing GE, SEL, Basler Electric, siemins, MG, ABB, Sea Pam
➢ Prepare safety precautions, procedures and regulations to control electrical and electronic schemes.
➢ Effective planning and prioritizing preventive maintenance and shutdowns.
➢ Skills to coordinate the activities of maintenance on plant for repair and new installations with contractors.
➢ Preparation of daily log, weekly report, checks sheets and project reports.
➢ Having proactive approach toward continual improvement in quality of skills, activities and maintenance processes.
➢ Good working relationship with labor, colleagues and other departments
➢ Skills of operating precession measure and calibration equipment’s.
➢ Understand drawings, blue prints, plans and specification methods of trouble shooting and complete control on maul functioning components.
➢ Supervise Preventive/predictive maintenance activities on plant like clean, check, test and calibrate.
➢ Discuss bids with vendors or other services.
➢ Provide technical assistance and advice to field person and contractors.
➢ Discuss, evaluate and coordinate activities with other sections of organization.
➢ Managed working hours, stress and resources within limited budget.
➢ Arranged meetings, made assessments accident reports.
Corrective, routine and preventive maintenance of 6.6kv/380volt dry type transformers up to 1500 KVA and testing and maintenance of the oil immersed transformer up to 390MVA, 21.5 KV to 500KV, Maintenance and overhauling of the OLTC.
Involved in Maintenance and troubleshooting in 500 KV GIS substation, breakers, isolators, earth switches, density monitors, Gas analysis and hydraulic drive units, gas filling, and other related jobs at substation.
Testing, routine maintenance and troubleshooting of protections relays and Circuit breakers of 6.6kv/6.3KV, buses, also commissioning, and testing.
Overhaul, preventive, corrective and routine maintenance of HV/MV motors up to 5MW, 6.6Kv.
Maintenance, online brush change, visual inspection and stator leak monitoring system on 323x4 MW, 18X2 MW generators,
Preventive and routine maintenance UPS battery chargers up to 80KVA.
Installation, sizing and trouble shooting of motor control centers.
Preventive, corrective, routine maintenance and troubleshooting of Excitation System (AVR).
CT testing polarity test, ratio test, saturation tests.
Well knowledge about the test equipments primary current injection test set, FREJA300, SVERKER 750 secondary current injection test set and relay test set, Circuit breaker analyzer, Digital Low Resistance Ohm meter, analog & digital megger up to 5000v, use of AVO meter and DOBLE M4000 multi function test set, Earth resistance tester, phase rotation check and sequence meter,
Permit accepter up to HV equipments and live.
Installation troubleshooting and maintenance of the variable speed drives, induction furnaces and forging presses.
Good knowledge of the installation, trouble shooting and maintenance of the actuators, like BIFFI, Rotork, Limi tork, Cibo.
I have worked on bagging at conveyers, belts, elevators, weighting scale indicator, hopper level indicators, automatic bagging machine, SOV, Air cylinder and load cells.
Good experience about transformer oil treatment, filling and testing.
Sizing, panel design, ordering and installation of Power factor panel and configuration of the power factor relay by ENTS, Nokian Capacitors and MG,
Installation of SKOV and Blue Earth climate controller and made panel for the MCC and data networking of controllers with infomatic web link.
Well knowledge about HT/LT cable sizing, laying, jointing, and termination.
Also preparing and maintaining equipment history card, call up card.
Maintenance, installation and testing of the cathodic protection.
SF^6 Gas filling, density monitors in GIS. Involved in trouble shooting GIS.
Good working relationship with labor, colleagues and other departments
Skills of operating precession measure and calibration equipments.
Understand drawings, blue prints, plans and specification methods of trouble shooting and complete control on maul functioning components.
Supervise Preventive/predictive maintenance activities on plant like clean, check, test and calibrate.
Discuss bids with vendors or other services.
Provide technical assistance and advice to field person and contractors.
Discuss, evaluate and coordinate activities with other sections of organization.
Managed working hours, stress and resources within limited budget.
Arranged meetings, made assessments accident reports.
Management
ECONOMICS
ELECTRICAL ENGINEERING