RajaRahim Abdul Malik

 Responsible for all quality control activities for allotted area of discipline.
 Familiar with overall project/construction scope of work.
 Compliance with the site’s health and safety regulations.
 Perform inspection according to applicable Engineering Standards, Procedures and applicable National and International Codes.
 Perform inspection according to applicable Engineering Standards, Procedures and applicable National and International Codes and Standard as SECO, NEC, NFPA, IEEE, IEC, CSA, ANSI, NEMA, NETA etc.,
 Inspection: Visual examination or dimensional evaluation of item and construction work operation to verify conformance to the predetermined quality requirements of the Client system of standards, drawings, and specification for the attainment of good quality as work progresses.
 Record inspection findings in an internal inspection logbook, follow up with the construction team to ensure that the activities complying with the quality requirements.
 Witness: To observe, watch over or visually examine a specific work operation, or test which others perform under the supervision of the field operation group.
 Surveillance: To progressively monitor by randomly witnessing and inspecting item & work operations before, during or after in process construction, give comments (if necessary), according to predetermined quality requirements.
 To co-ordinate, all activities in material handling, storage, preservation etc. as to ensure adequate protection & proper storage, handling, & preservation of the materials at site as per the manufacturer recommendation or standard requirements.
 Initiate / prepare & request for inspection (RFI) for client inspection for completed construction activities & for witness of starting pre-commissioning, pre-energized, & functional testing job activities.
 Highlighting all discrepancies detected during monitoring inspection and informing the same to QA/QC Manager.
 Reporting both verbally and in writing any non-conformance discovered.
 Prepare nonconformance reports (NCR) to the concerns and assist in developing corrective actions according to the approved quality plans, inspection test plans & relevant to client.
 Take immediate remedial to clear inspection logbook comments / pro-actives & close out the NCR's and relevant logbook entries after the implementation of the recommended corrective actions.
 Responsible to check & witnessing the pre-commissioning test

Project : R-APDRP
Client : TANGEDCO

Job Responsibilities:

 In charge for Chennai South Zone consisting of 48 Sub Stations & 354 Feeders.
 Coordinate to Prepare design for Erecting 33/11kv substations, 11kv/440v DTs, LT and HT Overhead Transmission line and UG Cables.
 Grounding system for 33/11kv substations.
 To implement GIS, Asset Data mapping and Consumer indexing within stipulated timeframe.
 Managing a Team of 45 Members.
 Co-ordinate with Client & Responsible for timely completion of site related works & Approvals.
 Preparing DPR and monthly Report for Meetings.

➢ Low Voltage Switchgears, Motor Control Centers (MCC), enclosed combination motor controllers, Power & Lighting Distribution Panels, Lighting Contactor Panels, Dry Type Transformers, and High Resistance Grounding System.
➢ Station Batteries, Battery Chargers, 125V-DC Distribution Panels, Uninterruptible Power Supply System (UPS)
➢ 2.4KV & 13.8KV Metal Clad Switchgears, 2.4KV Fire Water Pump Controllers (FWPC)
➢ Remote Control Panels for 69KV SF6 Hybrid Type Circuit Breakers, H5K.V SF6 Conventional type Circuit Breakers, 69KV Breaker Fail Protection Panels, 69KV Bus Bar Protection Panels, 69KV Cable Protection Panels, 69KV / 115KV Line Protection Panels, Revenue Metering Panels etc.
➢ Aluminum Ladder Type Cable Trays inside & outside of the service buildings (Horizontal & Vertical with complete accessories (H & V Tee, Elbow, Cross, Reducer, Blind end plates, Splice plates (Type: Expansion. Adjustable single & double bolts, Step down, cover, offset reducing etc.) Also bonding jumpers for electrical continuity / grounding.
➢ GRS-Conduit PVC Coated & Un-coated with all accessories for power & control wiring for fluorescent lighting fixtures, receptacle, and photocell controlled high-pressure sodium lighting fixtures (HPS) inside & outside of the service buildings
➢ Electric Metallic Tubing (EMT) inside the building / gypsum boards for LV cables, especially telecommunication cables.
➢ Complete grounding system (Mesh type) for the equipment's.

➢ Testing and commissioning of cables and electrical equipment's.


➢ Underground cable laying for grounding and lighting platform.

➢ Installation and termination of power cables through conduits.

➢ Day to day inspection in supervisor.

➢ Prepare documents for inspection and test report.

➢ Preparing DPR and monthly Report for Meetings.

Company: MAYTAS INFRA LIMITED
Project: RGGVY RE WORKS JAJPUR, 33/11KV FEEDER 33/11KV SUB STATION
Position: Electrical Engineer
Duration: Jun. 2008 to May 2009
Job Responsibilities:
➢ Distinctively been the in charge for electrification of Villages in Jajpur Dist, Orissa.
➢ Work Execution of 33/11 KV Substations, 33KV & 11 KV Feeders, Village Electrification works.

➢ Planning for the work activities, preparing Bill of Materials for both Substation and Village Electrification Works.
➢ Monitoring material issue to Sub-agencies and periodic material reconciliation's with sub-agencies.
➢ Preparing Monthly, Weekly rolling plans of work and material.
➢ Co-ordinate and accompany Client for material inspection.