Sr Process Engineer
NPCC Abu Dhabi
Total years of experience :18 years, 8 Months
ABU DHABI COMPANY FOR ONSHORE OIL OPERATIONS (ADCO)
BAB INTEGRATED FACILITIES PROJECT
\[New dewatering station at 5 RDS and New Train at BCDS\]
Project Type : Enquiry
Worked on Piping and Instrumentation Diagram (P&IDs) and update process P&IDs based project philosophies i.e isolation philosophy, Process design basis and philosophy specifications, operating & control philosophy, Flare Design philosophy etc.
Review & verify hydraulic calculation based on company specification.
Raised various RFCs (Requests for Clarification) to company with respect to project philosophies and FEED / ITT documents.
Update Feed documents i.e. P&IDs, Tie-in list etc BUNDUQ OSII PHASE DEVELOPMENT PROJECT
OFFSHORE WELLHEAD PLATFORM
Project Type : FEED CUM EPC PROJECT
(FEED as well as Detailed Engineering EPC Project)
Process simulation performed for offshore Wellhead platform (HYSYS -software)
Developed HYSYS cases of WHP for H&MB, same numbers additional cases for Choke Valve, MPFM, and Control Valve etc.
FLARENET simulation worked for in PSV inlet, outlet, vent header system sizing.
Prepared Process Flow diagrams (PFDs)
Prepared Process Safeguarding Diagram (PSFDs)
Developed Piping and Instrumentation Diagram (P&IDs) till issued for As BUILD.
Prepared Heat & Material Balance Diagram.
Prepared varies Instruments & Equipment Process Datasheet i.e Choke valve, Control valve, Flow Instruments, Temperature Instruments, Pressure Instruments, Open Drain Tank, Closed Drain Tank, Pig Launcher, Pig Receiver & Slug Catcher Process Datasheets etc.
Prepared Process Operating & Control philosophy, Safeguarding Philosophy & Start-up & shutdown philosophy
Prepared Pigging Procedure interlock and developed Pigging Procedure
Review / comments on Operating Manual Volume and Operating Procedures
Prepared Cause & Effect Diagrams( C&EDs)
Prepared Hazop Action Sheets and worked for Closures, Calculations & update all process related documents
Prepared Register for Safety Related Device (RSRD), Line List, Tie-in List & Utility Summary.
Prepared Package items Process Datasheet / Vendor offer reviews package items (As Listed Below)
- Multi-Phase Pump (MPP) Package
- Corrosion Inhibitor Package,
- Liquid Flow Metering Skid Package
- Multi-Phase Flow Meter Data Sheet (MPFM)
Participation in HAZOP / 3D piping / SIL Studies
PTTEP ZAWTIKA PHASE 1C DEVELOPMENT PROJECT
OFFSHORE WELLHEAD PLATFORM MYANMAR
Project Type : ENQUERY
Worked on Piping and Instrumentation Diagram (P&IDs) and update process P&IDs based project philosophies i.e isolation philosophy, Process design basis and philosophy specifications, operating control specification, Flare Design philosophy etc.
Review & verify hydraulic calculation based on company specification.
Datasheets.
Vendor proposal reviews of package items
OCCIDENTAL PETROLEUM OF QATAR LIMITED (OPQL)
OFFSHORE WELLHEAD PLATFORM OMAN (PHASE-5 PROJECT)
Project Type : ENQUERY
P&IDs, Technical Query to company which are contraction with FEED documents.
Update applicable documents i.e. P&IDs, Equipment & Instruments data sheets etc
Vendor offer reviews package items
ABU DHABI COMPANY FOR ONSHORE OIL OPERATIONS (ADCO) ~ Al Dhafra Petroleum
ONSHORE WELLHEAD PLATFORM
Project Type : Enquiry cum Detailed Engineering
PUMps & Vendor Offers
Multi-Phase Pump (MPP) vendors offer reviews
ABU DHABI MARINE OPERATING COMPANY (ADMA-OPCO) ~ AL YASAT PETROLEUM OPCO
OFFSHORE WELLHEAD PLATFORM - Bu Haseer Field Development Project - EPS
Project Type : Detailed Engineering Project
Worked on Piping and Instrumentation Diagram (P&IDs)
Prepared / updated Pigging operating Procedure, Process description, Tie-Ins Study Report
Worked on Tie in List, Fluid List, Pig Trap Datasheet, Instruments datasheet etc.
Prepared Cause & Effect Diagrams( C&EDs)
Prepared Hazop Action Sheets and worked for Closures, Calculations & update all process related documents
Prepared Package pdS
punch point resolution with technical justification
ENGINEERS INDIA LIMITED: 2005 TO TILL NOW ( 8.5 YEARS)
New Grass Root CDU/ VDU unit
Project phase: Basic Engineering Design Package preparation
Activities performed: • Simulation of CDU/VDU unit including Naphtha stabilizer, Naphtha Splitter of CDU/VDU Complex in PRO II and HYSIS.
• Prepared basic engineering design package of CDU/ VDU unit and generated stream summary, heat and material balance, Process Flow Diagram, Process & utility P&IDs, Hot and cold summary for exchangers/ air coolers, Heater Curve / simulation, Equipments datasheets, instrument datasheet, vessel sizing, Flare load Summary, utility & Chemical summary, Line list, PSV load calculation.
• Also performed the hydraulics calculation of this unit.
• Process package updation/compilation about client comments
PFCCU/PRU unit
Project phase: Detail Engineering Work
• Review of Licensor's Basic Engineering Design Package, mainly, Process Flow Diagram, heat and material balance, Piping and Instrumentation Diagram, Equipment datasheet, utility summary, flare load summary etc. in line with the MRPL Phase-III project philosophy and commented.
• Activities performed were detailed hydraulics of Pumped circuits, Column overhead circuits, compressor hydraulics etc.
• Prepared equipment and instrument datasheet.
• Review and follow up with vendor /Vendor item packages ( as listed Below)
➢ Flue Gas Cooler Package,
➢ TSS Vendor Package,
➢ MAB Vendor Package,
➢ WGC vendor Package,
➢ Slurry PA pump Turbine package,
➢ HWB pump Turbine package
➢ N2 blower package,
➢ Catalyst Loader Package
➢ Regenerrator Air Preheater Package
➢ SCSV/RCSV vendor
➢ Catalyst Bed material vendor (In PRU Section)
➢ Coalescers/ Settler/Pre-filters vendor from process point of view.
• Developed utility P&IDs, equipment/instrument datasheet of PFCCU / PRU section.
• Other activities involved were updating licensor line list, equipment datasheets etc.
• Participation in HAZOP study of PFCCU unit.
• Participation in 3D piping modeling of PFCCU unit.
• Participation with Logic DCS & PLC with vendor of PFCCU unit.
• Control & Logic DCS & PLC based
• Prepared Utility Summary & catalyst & chemical Summary
• Updation of Detailed engineering Process Package & compilation.
• KC logic Developed for PP-Mix Dryer &BED & RSH/COS/METHANOL BED REGENERATION
• Interaction /Resolution provide to client on licensor check listing of Erected Plant
Utility Offsites
Project phase: Refinery Utility
• Estimation of various utility consumption namely fuel gas, fuel oil, cooling water, power, steams etc. for the various units (DCU, DHT, CDU/VDU, CHT etc) under MRPL PH-III project and thereby arrived at the design basis of the offsite utility system.
Diesel Quality Up-gradation Project
Hydrocracker Revamp
Project phase: Hydro-cracker Revamp Design and Engineering (EPCM)
• Preparation of Process Package for Engineering and activities which involved simulation of CLPS section, updating of licensor P&ID & utilities P&IDs as a part of residual process engineering.
• Adequacy of existing equipments and instruments. Preparation of equipments and instrument datasheet.
Work process unit of Proposal Stage /Feasibility Report
Project phase: Proposal Stage /Feasibility Report
Review of Licensor's Process equipment summary,
Process Flow Diagram,
Material balance calculation/Review,
Utility requirement calculation/review
Catalyst & chemical summary review
added other additional equipment & system as required for costing
Site commissioning experience
Project phase: MRPL PFCCU/PRU UNIT
• Check listing of erected plant of PFCCU/PRU Unit
• Varies process related site issues (Process related) clarification /Resolutions provided to clients/Construction/Engineering with technical justification
.
Regards
Process Design Engineer
(Dy. Manager)
New Delhi, India
Education Qualification/ Institution/ Year:: B. Tech. (Chemical Engg) in 2005 from Indian Institute of Technology, IIT Kanpur, India Expected Time required for join if JOB offered to me 1 Month (Min.) Contact No / Mail-Id +91-9810092823/ raj.