RAKESH SOLANKI, INSTRUMENT SUPERVISOR

RAKESH SOLANKI

INSTRUMENT SUPERVISOR

knpc

Location
India - Vadodara
Education
Diploma, ELECTRONICS AND TELECOMMUNICATION
Experience
6 years, 2 Months

Share My Profile

Block User


Work Experience

Total years of experience :6 years, 2 Months

INSTRUMENT SUPERVISOR at knpc
  • Kuwait - Al Ahmadi
  • December 2012 to December 2013

Well versed with reading of P&I Dig, logic diagram, cause & effect diagram and junction box wiring Diagram. Strong background with refinery process control and instrument maintenance.
Carry out calibration of instruments and prepare test certificate and history card.
Checking of Bentley Nevada vibration 3300 & 3500 series. Installation, gap adjustment and investigation while tripping.
Assisting operation department during the changeover of compressor, pump, plant shutdown and start up activities.
Carry out breakdown and shutdown job of continues process plant and compressor.
Carry out the functional check of ESD and interlock of implementing new facility changes from operation request and loop check, sequence and logic checking of newly added facilities and package units.
To assist other sections such as Electrical, Mechanical, project department and workshop for the repair and troubleshooting of their instrument related work.

INSTRUMENT ENGINEER at DAEWOO E & C, SHELL PROJECT
  • Nigeria
  • September 2011 to April 2012

I worked with SHELL-AFAM 6 COMBINED CYCLE POWER PLANT (M/S. DAEWOO E & C)
Involved with commissioning and red line drawing team(156 MV gas turbine-02 nos. and 256 MV steam turbine). preparation of documentation and updated drawing for as built and submitted to client.

INSTRUMENT SUPERVISOR at HI TECH CONTROLS
  • India - Vadodara
  • July 2010 to August 2011

Supervision of commissioning activities like loop checking, Documentation, Loop check and function check with the various associated vendors. Work with responsibility in process control instrument and maintenance job and handling manpower distribution.

INSTRUMENT TECHNICIAN at ORYX GTL,QATAR
  • Other
  • April 2010 to May 2010

Replacing control valve link, overhauling of control valve, removing and fixing radial, axial and Temperature probes of steam turbine generator, recycle compressor.

INSTRUMENT TECHNICIAN at ADGAS,ABUDHABI
  • Other
  • October 2009 to November 2009

I was involved in LNG Train 2&3, Boiler 3&4, 5&6 overhaul (shut down).removing instru-ments from field for servicing at central work shop as per client list. On site overhauling and calibration of control valve, Replacing gland, studs & nuts of control valve, valve regulator, V/P converter, I/P converter and feedback arm, function checking of ESD related instru-ments. Calibration & checking of critical loops, Calibration & checking of Level troll, pressure switch, level switch. Installation of removing instruments in proper way & housekeeping af-ter competition of the job

INSTRUMENT TECHNICIAN at RAS LAFFAN OLEFINE COMPANY,QATAR
  • Other
  • January 2009 to July 2009

This is one of the largest ETHYLENE Plant (13 MMTPA). Carrying out pre-commissioning activities like loop checking, ESD and function check with the various associated vendors. CENTUM CS 3000 with VNET IP connectivity (YOKOGAWA), More than 2000 field bus foun-dation devices. Field Connex device from Pepperl + fiches for field bus distribution, Mother-board based power supply system (MB-FB-4R), Field bus power modules, advanced diag-nostic module(HD2-DM-A), modular surge protector, 8 channel segment protector & field bus terminator.

INSTRUMENT TECHNICIAN at ADGAS,ABUDHABI
  • Other
  • October 2008 to November 2008

I was involved in LNG Train 2&3, Boiler 3&4, 5&6 overhaul (shut down).removing instru-ments from field for servicing at central work shop as per client list. On site overhauling and calibration of control valve, Replacing gland, studs & nuts of control valve, valve regulator, V/P converter, I/P converter and feedback arm, function checking of ESD related instru-ments. Calibration & checking of critical loops, Calibration & checking of Level troll, pressure switch, level switch. Installation of removing instruments in proper way & housekeeping af-ter competition of the job

INSTRUMENT TECHNICIAN at KUWAIT NATIONAL PETROLIUM COMPANY
  • Other
  • June 2006 to July 2008

Ability to multitask, prioritize and work well under pressure, with minimal or no supervi-sion. Reporting to seniors and engineers, fault diagnose with the cause and effective draw-ings. Leads an instrument maintenance team, Performed servicing, calibration, installation of process control instrument. Day to day corrective & preventive maintenance for running plant as per KNPC standard operating procedures and safety standards, Carry out the func-tional checks of ESD and interlock system. Implementing new facility changes from opera-tion, Carrying out commissioning activities like loop checking, sequence and logic checking of newly added facilities and package units. Housekeeping and safe working practices.

Education

Diploma, ELECTRONICS AND TELECOMMUNICATION
  • at AICOMAS
  • April 2010
Diploma, INSTRUMENTATION & CONTROL
  • at IBME
  • October 2007
Diploma, INSTRUMENTATION
  • at INDUSTRIAL TRAINING INSTITUTE
  • July 1996

Specialties & Skills

Maintenance Services
Commissioning
Instrument Control
Maintanance,calibration,servicing,troubleshooting,commissioning,loop checking,function test,

Languages

English
Expert
Gujarati
Expert
Hindi
Expert

Training and Certifications

PROGRAMMABLE LOGIC CONTROLLER (Certificate)
Date Attended:
April 2011
Valid Until:
May 2011

Hobbies

  • reading