Maintenance Engineer
kepco kps
Total years of experience :11 years, 8 Months
Installation, testing and Commissioning of I&C instruments for 4*1400MW nuclear power plant .
Calibration of field instruments such as Rtd, Tc, Pressure switches, transmitters and gauges, flow transmitter,
level transmitters and switch, Temperature gauge and switch, Conductivity sensor, ph sensor etc.
Quintessential Professional with hands on General Management, various engineering
documents like P&IDs, data sheets & specifications of instruments, Loop Drawings, Logic Diagrams, GA
Drawings, Cable schedule, I/O schedule, Check list and Commissioning Procedures etc.
Performing activities for successful completion of all tasks including CAT and Punch List activities etc on time
with quality and safety.
Preparing permit to work for preventive maintenance, corrective maintenance, periodic calibration, replacement of instruments, inspection of I&C equipments.All Ptw are according to their specification like cold work, hot work, working at height, electrical work, confined space with the help of respective startup work request raised by the concern initiator.
Installation, testing and Commissioning of I&C instruments with proper procedure.
Calibration, preventive maintenence, corrective maintenance of field instruments such as Rtd, Tc, Pressure switches, transmitters and gauges, flow transmitter,
level transmitters and switch, Temperature gauge and switch, Conductivity sensor, ph sensor etc.
Quintessential Professional with hands on General Management, various engineering
documents like P&IDs, data sheets & specifications of instruments, Loop Drawings, Logic Diagrams, GA
Drawings, Cable schedule, I/O schedule, Check list and Commissioning Procedures etc.
Performing activities for successful completion of all tasks including CAT and Punch List activities etc on time
with quality and safety
I am currently working with
prayagraj power generation corporation Ltd from erection commissioning of 3×660 MW supercritical at Allahabad India with MAXDNA & Siemens SPPA T3000 TURBINE DCS erection commissioning of Demineralized plant, water intake & reservoir, water treatment. I am working here as I&C shift engineer and with experience of 7yrs+ month in operation & maintenance of boiler turbine generator and it's auxiliaries.
Installation, testing and Commissioning of DCS (maxDNA), Redundant Network system, Engineering
and operators work stations, Turbine stress controller, Unit control panels and GPS master/slave clocks.
➢ Knowledge of DCS configuration uploads & downloads to controllers, DPU flashing, Sequence of
event and alarm generation, DCS trends generation and field Input/output signals troubleshooting.
➢ Exposure to DCS control logics (permissive & interlock) for boiler & turbine auxiliaries, HT/ LT Drives
and breakers, process control loops and make changes to meet the system reliability and protect
frequent shutdown.
➢ Hands on experience of TSI probes (Make Megitt India & Shinkawa) installation and commissioning, Governing
Valve (Make Rexroth) and HP/LP bypass system (BHEL/Bomafa make) Commissioning.
➢ Commissioning and maintenance Of Integral/Non-integral MOVs (make auma, Limit torque and
Rotork, Flowserve), Pneumatic actuators (Mil, ABB, Frobes Marshall), Gate and dampers, Burner tilt Power
Cylinders, KGVs and Solenoid valves.
➢ Commissioning & maintenance of instruments associated with FSSS, SADC, Gravimetric Feeders
(BHEL make) and TG system (BHEL make) as per P&IDs and standard manuals.
➢ Conduct regular troubleshooting and root cause analysis of any failure Of Field instruments,
Analysers etc.
➢ Erection & commissioning of field instruments associated with HT/LT drives like BFP, CEP, ID, FD, PA,
Scanner air Fan (DC/AC), Seal air Fans, Coal Mills, Mill reject System, CW/DMCW pumps, CT fans etc.
➢ Commissioning of SWAS analysers, Soot blowing system, Chemical dosing system, ERV, FTP, Bunker
level monitoring system, CEMS, Opacity, O2, CO analysers
EPC Work & Technical Background:
➢ Successfully synchronized 3X660 MW TPP projects which include DCS logic and maxVUE HMI
graphics creation for boiler and turbine auxiliaries, System wise commissioning Protocols Checking, LIE/
LIR location plans etc.
➢ Calibration of field instruments such as Pressure switches, transmitters and gauges, flow transmitter,
level transmitters and switch, Temperature gauge and switch etc.
Review of basic engineering documents like DCS signal flow diagram, instrument data sheet and
specifications, calculation and bill certification of contractors (BHEL & PLL) etc. Control all contractors
performance for successful completion of all tasks including NCR and Punch List activities etc. on time
with quality and safety
➢Attending of daily defects which are raised by operation dept on SAP (SYSTEM ANALYSIS PROGRAM) for smooth & uninterrupted functioning of all units.
Completed B.E in electronics & instrumentation in 2011
URL removed due to policy violation. Please contact support for further information.