QC Engineer
ITP
مجموع سنوات الخبرة :12 years, 9 أشهر
Prepare project quality plan,
Conduct stage wise inspection of different equipment like Heat exchangers, Air coolers, column, Heaters and vessels.
Inspection of internal strip lining and weld overlay for corroded area of columns, re boiler and vessels.
Inspect the activities as per approved general scope, specific scope & Operational scope also IWL.
Shutdown : Takreer Ruwais Refinery (Gasoline & Condensate Turnaround 2014
Review Project Quality Plan to maintain and complying client requirements.
Review QA/QC Procedures and document control as submitted by the Contractors and ensure implementation is in compliance with agreement requirement.
Coordination of welding procedure qualification, Issue final welding book inclusive of WPS'S and PQR'S, Issuing method statement, if applicable
Inspection and Verify the correct storage, preservation of material and consumables.
Witness of procedure qualification tests, Check preparations and inspect work accordance with inspection test plan.
Monitoring site welding activities and to identify any eventual problem related to welding and NDT.
Review radiographic film & all NDT reports on a daily basis.
Investigate product quality problems, determine root cause, gather & analyse data to implement corrective action and reduce or eliminate cause.
Review work procedures and method statements for compliance with good work practices, Codes and customers contract specializations
Witnessing and sentencing of all site inspections within their disciplines
Monitoring the site welding activities, to identify any eventual problem related to welding and NDT.
Coordinate all site inspections with the site subcontractors
Ensure that all inspection reports are accurate and that all attached documents are current status
Ensure all work is correctly prepared prior to any inspection being undertaken.
Assist the site subcontractors in the resolution of drawing interpretation
Assist the site QC manager in the organisation, maintenance and control of the quality system.
Prepare non conformance reports to the QA manager and assist in developing corrective actions.
Coordinate with the customers QC inspectors for the resolution of site problems.
Test package review and complied with all related documents as per project specification.
The issuance of non-conformance reports in conjunction with the site QC manager.
Coordinate with NDT third party examination & testing agencies for the relevant testing and examination as to comply with the requirements of client.
Follow and compliance all site activity with site health and safety regulation.
Conducting stage wise inspection pipe spool fabrication and welding.
Performing visual inspection of welding at varies stage before, during & after.
Maintain welding consumable record and periodical inspection of welding consumables.
Monitoring site welding and NDT work.
Review NDT Reports as regular basis.
All inspection status report prepared at weekly & monthly basis.
Prepare project quality plan as per code, standard & contract requirements.
Train 1 & 4 Turnaround 2014
qualification tests
Visual, dimensional inspection and stage wise inspection of Pressure vessels, Composite air cooler, Pipe spool, Pipe supports & Structural Skid fabrication as per ITP.
Inspection and witness of load test for structural beam.
Monitoring site welding activities and inspect stage wise as per ITP.
Witness of PWHT & Review and approve PWHT procedures.
Review RT reports and NDT reports as per code & standards.
Witness of Hydro test, Leak test & Pneumatic test for varies Equipment’s like vessels, Pipe spools and reinforcement pad.
Ensure final painting inspection and witness of DFT for Pressure Vessels, Composite air cooler, Pipe spool and structural skid as per client specification.
Installation Inspection of Compressor, Engine and vessels mounting on the structural skid.
Inspect pipe spool routing as per P&ID and GA drawing.
Works monitoring during construction period and ensure safety & quality of work.
Ensure Non-Conformance Report (NCR) was raised once the activities deviate from the Contract Specifications or normal construction.
Coordinate with client inspection and complied all contractual requirements.
Review vendors MRB’s & ensure all the documents are endorsed as per ITP and submit to clients.
courses: Certified in CSWIP 3.1 Level II Certificate No-68498 ASNT Level – II : Radiography Testing (RT). ASNT Level – II : Ultrasonic Testing (UT). ASNT Level – II : Magnetic Particle Testing (MPT). ASNT Level – II : Dye Penetrant Testing (DPT).