Qa/qc Welding Inspector
Metito
Total years of experience :10 years, 10 Months
Responsible to organize in conjunction with construction all facilities required to conduct various NDT methods; monitor the progress of NDT, repair activities, etc.
Analyzed production accuracy to formulate corrective action plans.
Schedules inspection and test on a daily basis coordinating "hold point" witnessing by contractor/ third
party.
Report all non-conformances to the QCS/QCM.
Performed product inspections and reported results detailing errors, failures and non-conformance.
Liaised with QC engineer with regard to welding procedures and qualifications.
Drafted process documentation to standardize operating procedures and techniques.
Material receiving, inspection and review of documents and mill certificates, following up the standards
in order to maintain the quality in control
Qualification of Welders, Welding Procedures as per ASME SEC IX and following up to Saudi Aramco
check list.
Performing NDT on lifting lugs with approved procedure, Welding of steel structure as per AWS D1.1
Fabrication and Erection of Pipelines as per drawing with standard supports installation
Witnessing the NDT done as per required procedures.
Material receiving, inspection and review of mill test certificates
Attending quality control meetings with the client
Conduct line check to verify the overall completeness of installed piping system
Ensure that examination and test required by the inspection and test plan (ITP) had been performed with
satisfactory results
Inspect and witness pressure leak testing of valves prior to installation
Line checking of pipelines, which cover check-up for proper installation and location of standard pipe
supports and in accordance with Isometric Drawing
Inspect and witness re-instatement and bolt torquing of flanged joints prior to final piping completion
Co-ordination with third party inspection agencies
Preparation of work procedures, hydro test packages, repair work procedures and method statements.
Conduct close coordination with customer's inspection with regards to the inspection procedure and
acceptance and implementation of QA/QC procedures on fabrication steel piping, structural supports.
Strict implementation of approved welding procedures and spot audit for all portable oven consumable
used
Have good handling over welding of different types of materials and welding of dissimilar materials
Witnessing the NDT done as per required procedures
Have done welder qualification tests to approve the welder for different P no and F no
Witnessed PMI for the required austenitic stainless steels and also for Alloy steels.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT
methods; monitor the progress of NDT, repair activities, etc. through the Talisman standardized printouts. Responsible to effectively communicate the NDT status, general welding performance and the NDT subcontractor's performance.
Established field inspection and testing procedures for fabrication, welding and piping.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT methods; monitor the progress of NDT, repair activities, etc.
Analyzed production accuracy to formulate corrective action plans.
Schedules inspection and test on a daily basis coordinating "hold point" witnessing by contractor/ third
party.
Report all non-conformances to the QCS/QCM.
Performed product inspections and reported results detailing errors, failures and non-conformance.
Liaised with QC engineer with regard to welding procedures and qualifications.
Drafted process documentation to standardize operating procedures and techniques.
Material receiving, inspection and review of documents and mill certificates, following up the standards
in order to maintain the quality in control
Qualification of Welders, Welding Procedures as per ASME SEC IX and following up to Saudi Aramco
check list.
Performing NDT on lifting lugs with approved procedure, Welding of steel structure as per AWS D1.1
Fabrication and Erection of Pipelines as per drawing with standard supports installation
Witnessing the NDT done as per required procedures.
Material receiving, inspection and review of mill test certificates
Attending quality control meetings with the client
Conduct line check to verify the overall completeness of installed piping system
Ensure that examination and test required by the inspection and test plan (ITP) had been performed with
satisfactory results
Inspect and witness pressure leak testing of valves prior to installation
Line checking of pipelines, which cover check-up for proper installation and location of standard pipe
supports and in accordance with Isometric Drawing
Inspect and witness re-instatement and bolt torquing of flanged joints prior to final piping completion
Co-ordination with third party inspection agencies
Preparation of work procedures, hydro test packages, repair work procedures and method statements.
Conduct close coordination with customer's inspection with regards to the inspection procedure and
acceptance and implementation of QA/QC procedures on fabrication steel piping, structural supports.
Strict implementation of approved welding procedures and spot audit for all portable oven consumable
used
Have good handling over welding of different types of materials and welding of dissimilar materials
Witnessing the NDT done as per required procedures
Have done welder qualification tests to approve the welder for different P no and F no
Witnessed PMI for the required austenitic stainless steels and also for Alloy steels.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT
methods; monitor the progress of NDT, repair activities, etc. through the Talisman standardized printouts. Responsible to effectively communicate the NDT status, general welding performance and the NDT subcontractor's performance.
Established field inspection and testing procedures for fabrication, welding and piping.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT methods; monitor the progress of NDT, repair activities, etc.
Analyzed production accuracy to formulate corrective action plans.
Schedules inspection and test on a daily basis coordinating "hold point" witnessing by contractor/ third
party.
Report all non-conformances to the QCS/QCM.
Performed product inspections and reported results detailing errors, failures and non-conformance.
Liaised with QC engineer with regard to welding procedures and qualifications.
Drafted process documentation to standardize operating procedures and techniques.
Material receiving, inspection and review of documents and mill certificates, following up the standards
in order to maintain the quality in control
Qualification of Welders, Welding Procedures as per ASME SEC IX and following up to Saudi Aramco
check list.
Performing NDT on lifting lugs with approved procedure, Welding of steel structure as per AWS D1.1
Fabrication and Erection of Pipelines as per drawing with standard supports installation
Witnessing the NDT done as per required procedures.
Material receiving, inspection and review of mill test certificates
Attending quality control meetings with the client
Conduct line check to verify the overall completeness of installed piping system
Ensure that examination and test required by the inspection and test plan (ITP) had been performed with
satisfactory results
Inspect and witness pressure leak testing of valves prior to installation
Line checking of pipelines, which cover check-up for proper installation and location of standard pipe
supports and in accordance with Isometric Drawing
Inspect and witness re-instatement and bolt torquing of flanged joints prior to final piping completion
Co-ordination with third party inspection agencies
Preparation of work procedures, hydro test packages, repair work procedures and method statements.
Conduct close coordination with customer's inspection with regards to the inspection procedure and
acceptance and implementation of QA/QC procedures on fabrication steel piping, structural supports.
Strict implementation of approved welding procedures and spot audit for all portable oven consumable
used
Have good handling over welding of different types of materials and welding of dissimilar materials
Witnessing the NDT done as per required procedures
Have done welder qualification tests to approve the welder for different P no and F no
Witnessed PMI for the required austenitic stainless steels and also for Alloy steels.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT
methods; monitor the progress of NDT, repair activities, etc. through the Talisman standardized printouts. Responsible to effectively communicate the NDT status, general welding performance and the NDT subcontractor's performance.
Established field inspection and testing procedures for fabrication, welding and piping.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT methods; monitor the progress of NDT, repair activities, etc.
Analyzed production accuracy to formulate corrective action plans.
Schedules inspection and test on a daily basis coordinating "hold point" witnessing by contractor/ third
party.
Report all non-conformances to the QCS/QCM.
Performed product inspections and reported results detailing errors, failures and non-conformance.
Liaised with QC engineer with regard to welding procedures and qualifications.
Drafted process documentation to standardize operating procedures and techniques.
Material receiving, inspection and review of documents and mill certificates, following up the standards
in order to maintain the quality in control
Qualification of Welders, Welding Procedures as per ASME SEC IX and following up to Saudi Aramco
check list.
Performing NDT on lifting lugs with approved procedure, Welding of steel structure as per AWS D1.1
Fabrication and Erection of Pipelines as per drawing with standard supports installation
Witnessing the NDT done as per required procedures.
Material receiving, inspection and review of mill test certificates
Attending quality control meetings with the client
Conduct line check to verify the overall completeness of installed piping system
Ensure that examination and test required by the inspection and test plan (ITP) had been performed with
satisfactory results
Inspect and witness pressure leak testing of valves prior to installation
Line checking of pipelines, which cover check-up for proper installation and location of standard pipe
supports and in accordance with Isometric Drawing
Inspect and witness re-instatement and bolt torquing of flanged joints prior to final piping completion
Co-ordination with third party inspection agencies
Preparation of work procedures, hydro test packages, repair work procedures and method statements.
Conduct close coordination with customer's inspection with regards to the inspection procedure and
acceptance and implementation of QA/QC procedures on fabrication steel piping, structural supports.
Strict implementation of approved welding procedures and spot audit for all portable oven consumable
used
Have good handling over welding of different types of materials and welding of dissimilar materials
Witnessing the NDT done as per required procedures
Have done welder qualification tests to approve the welder for different P no and F no
Witnessed PMI for the required austenitic stainless steels and also for Alloy steels.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT
methods; monitor the progress of NDT, repair activities, etc. through the Talisman standardized printouts. Responsible to effectively communicate the NDT status, general welding performance and the NDT subcontractor's performance.
Established field inspection and testing procedures for fabrication, welding and piping.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT methods; monitor the progress of NDT, repair activities, etc.
Analyzed production accuracy to formulate corrective action plans.
Schedules inspection and test on a daily basis coordinating "hold point" witnessing by contractor/ third
party.
Report all non-conformances to the QCS/QCM.
Performed product inspections and reported results detailing errors, failures and non-conformance.
Liaised with QC engineer with regard to welding procedures and qualifications.
Drafted process documentation to standardize operating procedures and techniques.
Material receiving, inspection and review of documents and mill certificates, following up the standards
in order to maintain the quality in control
Qualification of Welders, Welding Procedures as per ASME SEC IX and following up to Saudi Aramco
check list.
Performing NDT on lifting lugs with approved procedure, Welding of steel structure as per AWS D1.1
Fabrication and Erection of Pipelines as per drawing with standard supports installation
Witnessing the NDT done as per required procedures.
Material receiving, inspection and review of mill test certificates
Attending quality control meetings with the client
Conduct line check to verify the overall completeness of installed piping system
Ensure that examination and test required by the inspection and test plan (ITP) had been performed with
satisfactory results
Inspect and witness pressure leak testing of valves prior to installation
Line checking of pipelines, which cover check-up for proper installation and location of standard pipe
supports and in accordance with Isometric Drawing
Inspect and witness re-instatement and bolt torquing of flanged joints prior to final piping completion
Co-ordination with third party inspection agencies
Preparation of work procedures, hydro test packages, repair work procedures and method statements.
Conduct close coordination with customer's inspection with regards to the inspection procedure and
acceptance and implementation of QA/QC procedures on fabrication steel piping, structural supports.
Strict implementation of approved welding procedures and spot audit for all portable oven consumable
used
Have good handling over welding of different types of materials and welding of dissimilar materials
Witnessing the NDT done as per required procedures
Have done welder qualification tests to approve the welder for different P no and F no
Witnessed PMI for the required austenitic stainless steels and also for Alloy steels.
Responsible to organize in conjunction with construction all facilities required to conduct various NDT
methods; monitor the progress of NDT, repair activities, etc. through the Talisman standardized printouts. Responsible to effectively communicate the NDT status, general welding performance and the NDT subcontractor's performance.
Established field inspection and testing procedures for fabrication, welding and piping.
i am diploma in mechanical engineering
URL removed due to policy violation. Please contact support for further information.