Mechanical Commissioning Supervisor
Gulf Piping CO
Total years of experience :7 years, 4 Months
Report to the mechanical commissioning engineer.
ÿ Interfaces with other disciplines to ensure integration of activities
ÿ scheduling and coordinating work to tight deadlines
ÿ Lead craft supervision for a wide range of mechanical equipment and system testing & pre-commissioning activities
ÿ Implement & Test the subsystems as per project commissioning test sheets
ÿ Monitoring Mechanical Completion progress punch status
ÿ Verify Marine side systems Piping & Mechanical disciplines with P&ID, ISO and vendor equipment drawing and point
out punches
ÿ Perform inter-discipline checks
ÿ Coordinates Mechanical Spare Parts - ensure that they are all available for pre-commissioning use and in the
warehouse
ÿ Support pre-commissioning activities, such as lube oil flushing, seal system flushing and charging, chemical cleaning,
final alignment and coupling installation
ÿ Participate in walk downs, mechanical checks, vessel closures and installation of filters/ spades/blinds
ÿ Execute specific specialist pre-commissioning activities (in coordination with system engineers ) such as leak testing,
air freeing, flooding, filling, coupled pump runs and removal/reinstate suction/discharge valves
ÿ Preparation of method statements, procedures and routines where required
ÿ Reports on work progress, bringing to notice potential problems or delays and recommends solutions
ÿ Plan, Monitor and assist in Vendor activities as required
ÿ Supports LOTO activities during work preparation, and confirms 100% compliance of craft sign on/off
ÿ Compliance in accordance with HSE Standards
Projects Accomplished:
Project Title: Sagar Samrat Conversion Project from MODU to MOPU
Client: ONGC
Project Title: NDC AL YASAT - RIAP
Client: National Drilling Co (NDC
Project Title: 125/300 self propelled and elevated jack up crane barge with accommodation
Client: Gulf Drilling International, Qatar.
Successfully Done:
I have commissioned marine and rig equipments like
ÿ Rig Air Compressors
ÿ Oily Water Separators
ÿ Shale Shakers
ÿ Mud Agitators
ÿ Sewage Treatment plant
ÿ Different rotating equipments like charging pumps, mixing pumps etc.
ÿ Commissioned different marine side systems like Fuel Oil system, Compressed air system, Bilge System, Ballast
system, Sea water system, Sewage treatment system etc
Operations and Maintenance
Planning and effectuating predictive & preventive maintenance schedules for equipments; conducting periodic checks to ensure performance of various equipments.
Preparing the shift report, machine status report and manpower utilization during shift and pending jobs; identifying areas of defects; conducting service/repair to rectify equipments.
Establishing quality standards, implementing stringent quality control systems for incoming materials to enhance quality of products & reduce the rejection rate.
Installation/ Testing/ Commissioning
Foreseeing performance bottlenecks and taking corrective measures to avoid the same
Managing erection, commissioning, inspection tests of equipments & providing utility services to the equipments.
Installing, Commissioning &trouble shooting problems arising in the total execution of job
Notable Accomplishments
Successfully managed the installation of:
• Various sizes of Pipes, Flow Meters, Nozzles as per national / international standards.
• Various rotating equipments like Blower, Compressor etc.
• Various sizes and types of valves in the pipe loops.
Efficiently inspected and witnessed:
• Non destructive Test (NDT) like Dye Penetrating Test in the welded joints and flanges in the pipe.
• Hydro test of pipes and Flow Meters as per standard.
Played a key role in testing of flow products like Safety Releif valves, Butterfly valves, etc. as per the relevant test codes/ standards.
Distinction of conducting model approval of flow meters and other flow products as per AGA, OIML, ANSI, BS EN and IS standards.
Project of Improvements of facilities on Liquefied Natural Gas Plant of Basic Chemical Industries Ltd, Jubail, KSA.
Supervision of valves manufactures & re-matching as per customers specification drawing and plan drawing
Experienced in reading P&ID & plan drawing and ISO drawing Coordinating with Engineering and Construction and liaise with the Client on detail engineering requirements.
Report daily progress achievements and concerns on work-in-hand. Ensure that all work is carried out in accordance with project specifications / procedures / method statements and schedule shall report back if any deviations observed
Inspection of fabricated materials and parts before assembling.
Manpower and material arrangements for the implementation of the project.
Planning the day to day activities of erection equipments with the help of superiors.
Routine checking, condition monitoring of equipments.
Preventive maintenance schedule preparation of all equipments.
Assisted our superiors in quality activitie
Bachelor of Engineering in Mechanical Engineering from ANNA University, Chennai, India.