Abubakar siddiq

•Responsible for providing technical support to site team and take corrective action if necessary.
•Follow up site activities on daily, weekly and monthly basis with them to complete job within time frame.
•Review shop drawings, coordinate with client, consultant and local authorities.
•Attending weekly as well as monthly meetings with client and consultant to discuss progress and further planning.
•Managing and planning material procurement, Equipment and manpower as per project requirements.
•Prepared daily work plan and submit to project management to review and approval.
•Supervise quality control and safety matters on at site.
•Site Supervision of Installation of HV Power & Fiber optic cable and HV Cable & Fiber Jointing/Splicing & Terminations.
•As-built drawings review and submittals provision.
•Preparing Joint Measurements, as built drawings coordinate with Saudi Electric Company management for signed and approval up to final invoicing.
•Preparation and follow up NCR by concerned supplier or manufacturer
•Inspection before pulling cable route Direct buried, HDD portion Duct banks, Man holes and preparation for cable
•Cable Meggering and Sheath testing before pulling cable on drum at site.
•110 KV Cable pulling, Splicing, Link Boxes installation and termination & Joint Bays groundings
•Cable termination Outdoor and indoor Sealing Ends
•Schedule preparation for sealing end plug in and HV test.
•Fiber optic splicing in Rack S/S communication room and splicing with OPGW in Over Head Line Towers
•Testing commissioning FO cable (End to End) test OTDR & power meter 1310nm, 1550nm & 1625nm.
•Gassing/Degassing GIS terminals
•Gantry works installation of post insulator, surge arrester bus bar installation, jumper conductor installation torqueing and surge counter installation and connections
•HV cable High Voltage test /sock test and related to all routine cable tests
•Preparation of Shutdown Schedule and get approval from client
•Inspect all type material as per SEC standards

Different type of Electrical Test performs under my Supervision
 Cable insulation Resistance test
 SVL Insulation Resistance
 DC Voltage test on outer sheath
 Zero sequence Impedance test
 Capacitance Measurement test
 Cross bonding check
 Circuit phasing check
 Ground resistance of Earthing point
 Conductor resistance test
 Link contact resistance
 Positive/Negative sequence impedance
 TDR Test
 High Voltage test

•Organize, implement, conduct and manage the QA/QC programs.
•Coordinate the document controls of technical submittals, drawings, etc with the project team and to ensure that the QA/QC validation has been done, to ensure their issue, amendment and recall of controlled documents.
•Coordinate all inspections, monitor the required tests and record inspections and tests made pas the contract plan and specifications.
•Liaise with the client’s representative for the conduct of day to day quality related project activities.
•Coordinate with the project manager regarding work performance and hold authority to stop work in any area where discrepancies remain uncorrected and/or cancel the stop work order upon satisfactory correction of noted deficiencies.
•Provide technical support to the project manager and guidance to site staff in submission of materials for approval, request for inspection, shop drawings, As-built drawings O & M manual.
•Assist QA/QC Manager in conducting internal quality audits.
•Ensure that Non-conformance Report (NCR) are raised once the activities deviated from the contract specifications.
•Coordinate with the project staff to compile and maintain pertinent records of inspection and testing until end contract and all pertinent records for retention on completion of project.
•Attend Monthly Project Review Meetings (PRM) and alert the project team of any potential problems.
•Site Inspection RFI;s preparation and coordinates with NG Consultants (Electrical, Materials & Mechanical).

•Documentation of daily work progress and maintaining quality control protocol of site working.
•Mechanical erection of gantries, earth mast, steel structure for equipment, power transformer, CB, CT, surge arrester, Isolators, Panels and grounding mesh engineering for building and switch yard lighting protection.
•Cable laying and termination designing according to schematic diagram and testing to ensure connections.
•Stringing of bus bar and earth shield wire.
•Raise the RFI’s and RMI’s
•Make NCR’s and MDR Reports.
•Inspect all the work electrical, mechanical & civil according to
the schematic.
•Working as a site commercial.

Installation of Protection Relays, Auxiliary Relays, Circuit Breaker, CT, CP,
Different type of meters, Selector switches etc.
Wiring of different equipment in panels according to drawing.
Function test of Protection Panels.
Study and Modified the Electrical drawings
Check and Test complete panels according to drawing.