ELECTRICAL ENGINEER
POWERON ENGINEER
Total years of experience :16 years, 2 Months
Tacking electrical contract from the client design the system asper requirement
On request, monitor construction, testing, and commissioning work executed by the construction contractors for compliance with the project specification.
Preparation of requisitions and technical evaluation of subsequent bids for Electrical material and equipment purchases.
General supervision and inspect the installation, modification and commissioning of electrical systems at construction sites.
Monitor, verify, and document the work being performed through subordinates.
To ensure proper implementation of design at site.
Provide To ensure design packages meet the required safety, environmental and ergonomic standards.
technical assistance to the construction team as needed.
Generate/Review material requisitions, submittals, and ensure contract performance measures are met.
Ensure that all electrical site activities are conducted under controlled conditions as per shop drawings, method statements, specification and work plan.
Coordinating with other engineering discipline
Load calculation
Transformer selection
Generator selection
Cable sizing
Installation
modification as per site requirement
Active interface between client and contractors for technical and nontechnical issues in the project.
to complete the project in the target time.
Ensuring by inspection & verification that the contractor prepares final drawing for the project and compliance with what has been implemented
Install the transformer
Generator installation
Motor installation
Cabling Review of design packages and drawings and other vendor documentations of the project for the conformity of the standards of client for full filling the project scope.
Responsible for the meeting with the client and contractor for making and review the status master plan, execution schedule, progress of the project.
Monitoring and managing all the steps of project execution to meet the client requirement and standards by ensuring the safety, quality and technical policies and procedures are practiced during the execution of the project.
Monitoring and supervision substation projects inside plant.
Scheduling, monitoring and supervision of testing & commissioning activities.
Co-ordination with different departments in client side to ensure the permits and witness from the maintenance department
Supply power to TBM, Shutter machine, Concrete pump
Tunnel lighting
Construction of 115/13.8 GIS substation
Preparation of remote end site survey report.
Revision & verification of GIS, SWGR & Protection schemes before submission to the consultant for approval.
Arrangement of management- subcontractor, management consultant meetings.
Attend the review & progress meeting with consultant and subcontractors.
Design - Protection co-ordination.
Design - Construction co-ordination.
Preparation of cable schedule.
Preparation of testing plan, weekly, daily testing schedule & DPR.
Arranging work front to testing team. In fast track site without disturbing construction activity and vice versa.
Transformer installation
Transformer testing
Panel board erection
Capacitor bank installation
Familiarization of routine MAINTENANCE & Break down works of 66KV GIS Substation.
Maintenance of transformers, bay, bus, circuit breakers, control circuits
Control and protection panel erection and all control wiring.
Conducted various Testing of transformer and Breakdown Voltage test, Insulation resistance Measurement & overhauling of OLTC.
11KV Pilot wire protection cable joining end termination work Trouble shooting of requirements and control circuit wiring. Maintenance of sub-station battery and battery charger.
Designing and Drafting of 33 KV Underground cable feeder from 110 KV sub-station, Thirumala to 33KV Sub-Station karamana
Switching operations of 66kV, 33kV & 11kV feeder breakers from control room.
Sequential switching operations of transformers and feeders from Switch yard.
Manual operations of isolators, earth switch and breakers.
Manual adjustments of system voltage using tap changer.
Power factor adjustment by capacitor bank switching.
Issuing NBC to the operator of remote end substations.
Issuing PTW certificate.
Implementation of load shedding according to system requirement.
Preparation operation daily log book and load flow chart.
Test charging of tripped feeders to check healthiness before informing to emergency maintenance section.
Issuing blink on feeders to isolate some portion of feeder
Transformer maintenance- IR test, oil level & leakage check, breather check & silica gel changing, OLTC function check, Fan condition check, Bucholtz, WTI, OTI alarm & trip check, Oil BDV test, Secondary injection test on relays.
Electrical and manual operation & spring charge check on circuit breaker, Alignment & operation check on isolators and earth switches. VCB operation check in service, Test & racked out positions, General inspection of condition of CT and VT.
Cross checking the drawings before work starts.
Supervising of electrical works.
Electrification of buildings.
Erection of panel boards.
Fire pumps installation & AC installation, Installation of 11KV transformer up to 5ooKva.
Installation, testing & commissioning of electrical equipments
in