Electrical & Instrumentation QC Inspector
NPCC
Total years of experience :14 years, 0 Months
• Always work Safety first.
• Deals with reviewing of all ITP\'s/QCP/Method Statement/ Material Approval prior for project plan preparation.
• Coordinating with Construction Supervisor project plan drawing review-having AFC drawing officially approved documentation.
• Represent Company during weekly meeting concerning schedule plan activity and project plan on all tools and equipment needed for construction.
• Assigned to Review all Subcontractor Technical Documentation Circulation prior approval to all concerned lead official.
• Ensured instrument equipment works complied with project specifications, company procedures, method statements and quality assurance and controls documentation (strictly implementing the ISO 2000 and ISO 9000).
• Supervised and monitoring the flow of inspection on-site and calibration prior to meet the project deadline.
• Able to analyzed every area to be survey and witness prior for RFI to be offered to the main client for inspection.
• Assigned to witnessi
• Always work Safety first.
• Material verification and Take store keeping of instrument material under control to be under a proper
Condition to avoid any damage or bad effect during warehousing
• Correct interpretation of equipment labels, IP Rating etc.
• Promptly report and document in all instances of nonconformance.
• Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications..
• Insure that all necessary inspections as identified in the approved Inspection
and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
• Ensure that the production quality being offered for inspection meets the client’s
requirements and Monitor and report Key Performance.
• Ensure that all deviations from the Project Quality Program and the Company
integrated management system (IMS) are documented and recorded.
• Coordinate the generation of client Requests for Inspections (RFI) where required
providing sufficient notice for Hold, witness and inspection Points.
• Review & check documents for instrument loop folder package prior to final walk down.
• Review final Dossiers documents if the attachment’s complete prior to handover.
• Inspect each instrument against data sheet prior to release to site for installation.
• Inspect instrument stanchions, location, mounting height, orientation etc.
• Inspect installation of Instruments including glanding termination of cables.
• Inspect installation/hook up and pressure test of impulse tubing and air supply/signal lines.
• Inspect installation of supports prior to cable tray installation.
• Inspection of cable tray/conduit installation prior to release for cable laying.
• Inspect UG stub-ups and instrument earthing of panels, cables etc.
• Inspect cable trench for sand bedding prior to cable laying and release each layer.
• Inspect cable segregation arrangement etc prior to back filling.
• Inspect cable glanding, termination, dressing of cable wiring inside each JB’s and local panels.
• Inspect installation of various control panels, consoles, desks.
• Inspect internal cable tray works prior to installation of cables.
• Inspect installation of various cables including system cables.
• Inspect installation of various F&G instruments, control panels.
• Witness calibration of each instrument as required by ITP/specifications.
• Witness pressure/leak testing of air supply/signal lines/pressure test of impulse tubes.
• Witness inspection/test related to analyser houses.
• Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination.
• Witness testing of the F&G circuits and system as applicable and loop continuity checking.
• Verify completion of heat tracing for impulse tubes.
• Verify all inspections related each loop components have been carried out as per applicable ITP’s and documented.
•Always work Safety first.
•Material verification and Take store keeping of instrument material under control to be under a proper condition to avoid any damage or bad effect during warehousing
•Correct interpretation of equipment labels, IP Rating etc.
•Promptly report and document in all instances of nonconformance.
•Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications.
•Insure that all necessary inspections as identified in the approved Inspection and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
•Ensure that the production quality being offered for inspection meets the client’s requirements and Monitor and report Key Performance.
•Ensure that all deviations from the Project Quality Program and the Company integrated management system (IMS) are documented and recorded.
•Coordinate the generation of client Requests for Inspections (RFI) where required providing sufficient notice for Hold, witness and inspection Points.
•Review & check documents for instrument loop folder package prior to final walk down.
•Review final Dossiers documents if the attachment’s complete prior to handover.
•Inspect each instrument against data sheet prior to release to site for installation.
•Inspect instrument stanchions, location, mounting height, orientation etc.
•Inspect installation of Instruments including glanding termination of cables.
•Inspect installation/hook up and pressure test of impulse tubing and air supply/signal lines.
•Inspect installation of supports prior to cable tray installation.
•Inspection of cable tray/conduit installation prior to release for cable laying.
•Inspect UG stub-ups and instrument earthing of panels, cables etc.
•Inspect cable trench for sand bedding prior to cable laying and release each layer.
•Inspect cable segregation arrangement etc prior to back filling.
•Inspect cable glanding, termination, dressing of cable wiring inside each JB’s and local panel.
•Inspect installation of various control panels, consoles, desks.
•Inspect internal cable tray works prior to installation of cables.
•Inspect installation of various cables including system cables.
•Inspect installation of various F&G instruments, control panels.
•Witness calibration of each instrument as required by ITP/specifications.
•Witness pressure/leak testing of air supply/signal lines/pressure test of impulse tubes.
•Witness inspection/test related to analyser houses.
•Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination.
•Witness testing of the F&G circuits and system as applicable and loop continuity checking.
•Verify completion of heat tracing for impulse tubes.
•Verify all inspections related each loop components have been carried out as per applicable ITP’s and documented.
•Always work Safety first.
•Material verification and Take store keeping of instrument material under control to be under a proper condition to avoid any damage or bad effect during warehousing
•Correct interpretation of equipment labels, IP Rating etc.
•Promptly report and document in all instances of nonconformance.
•Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications.
•Insure that all necessary inspections as identified in the approved Inspection and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
•Ensure that the production quality being offered for inspection meets the client’s requirements and Monitor and report Key Performance.
•Ensure that all deviations from the Project Quality Program and the Company integrated management system (IMS) are documented and recorded.
•Coordinate the generation of client Requests for Inspections (RFI) where required providing sufficient notice for Hold, witness and inspection Points.
•Review & check documents for instrument loop folder package prior to final walk down.
•Review final Dossiers documents if the attachment’s complete prior to handover.
•Inspect each instrument against data sheet prior to release to site for installation.
•Inspect instrument stanchions, location, mounting height, orientation etc.
•Inspect installation of Instruments including glanding termination of cables.
•Inspect installation/hook up and pressure test of impulse tubing and air supply/signal lines.
•Inspect installation of supports prior to cable tray installation.
•Inspection of cable tray/conduit installation prior to release for cable laying.
•Inspect UG stub-ups and instrument earthing of panels, cables etc.
•Inspect cable trench for sand bedding prior to cable laying and release each layer.
•Inspect cable segregation arrangement etc prior to back filling.
•Inspect cable glanding, termination, dressing of cable wiring inside each JB’s and local panel.
•Inspect installation of various control panels, consoles, desks.
•Inspect internal cable tray works prior to installation of cables.
•Inspect installation of various cables including system cables.
•Inspect installation of various F&G instruments, control panels.
•Witness calibration of each instrument as required by ITP/specifications.
•Witness pressure/leak testing of air supply/signal lines/pressure test of impulse tubes.
•Witness inspection/test related to analyser houses.
•Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination.
•Witness testing of the F&G circuits and system as applicable and loop continuity checking.
•Verify completion of heat tracing for impulse tubes.
•Verify all inspections related each loop components have been carried out as per applicable ITP’s and documented.
•Always work Safety first.
•Material verification and Take store keeping of instrument material under control to be under a proper condition to avoid any damage or bad effect during warehousing
•Correct interpretation of equipment labels, IP Rating etc.
•Promptly report and document in all instances of nonconformance.
•Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications.
•Insure that all necessary inspections as identified in the approved Inspection and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
•Ensure that the production quality being offered for inspection meets the client’s requirements and Monitor and report Key Performance.
•Ensure that all deviations from the Project Quality Program and the Company integrated management system (IMS) are documented and recorded.
•Coordinate the generation of client Requests for Inspections (RFI) where required providing sufficient notice for Hold, witness and inspection Points.
•Review & check documents for instrument loop folder package prior to final walk down.
•Review final Dossiers documents if the attachment’s complete prior to handover.
•Inspect each instrument against data sheet prior to release to site for installation.
•Inspect instrument stanchions, location, mounting height, orientation etc.
•Inspect installation of Instruments including glanding termination of cables.
•Inspect installation/hook up and pressure test of impulse tubing and air supply/signal lines.
•Inspect installation of supports prior to cable tray installation.
•Inspection of cable tray/conduit installation prior to release for cable laying.
•Inspect UG stub-ups and instrument earthing of panels, cables etc.
•Inspect cable trench for sand bedding prior to cable laying and release each layer.
•Inspect cable segregation arrangement etc prior to back filling.
•Inspect cable glanding, termination, dressing of cable wiring inside each JB’s and local panel.
•Inspect installation of various control panels, consoles, desks.
•Inspect internal cable tray works prior to installation of cables.
•Inspect installation of various cables including system cables.
•Inspect installation of various F&G instruments, control panels.
•Witness calibration of each instrument as required by ITP/specifications.
•Witness pressure/leak testing of air supply/signal lines/pressure test of impulse tubes.
•Witness inspection/test related to analyser houses.
•Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination.
•Witness testing of the F&G circuits and system as applicable and loop continuity checking.
•Verify completion of heat tracing for impulse tubes.
•Verify all inspections related each loop components have been carried out as per applicable ITP’s and documented.
• Always work Safety first.
• Material verification and Take store keeping of instrument material under control to be under a proper
Condition to avoid any damage or bad effect during warehousing
• Correct interpretation of equipment labels, IP Rating etc.
• Promptly report and document in all instances of nonconformance.
• Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications..
• Insure that all necessary inspections as identified in the approved Inspection
and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
• Ensure that the production quality being offered for inspection meets the client’s
requirements and Monitor and report Key Performance.
• Ensure that all deviations from the Project Quality Program and the Company
integrated management system (IMS) are documented and recorded.
• Coordinate the generation of client Requests for Inspections (RFI) where required
providing sufficient notice for Hold, witness and inspection Points.
• Review & check documents for instrument loop folder package prior to final walk down.
• Review final Dossiers documents if the attachment’s complete prior to handover.
• Inspect each instrument against data sheet prior to release to site for installation.
• Inspect instrument stanchions, location, mounting height, orientation etc.
• Inspect installation of Instruments including glanding termination of cables.
• Inspect installation/hook up and pressure test of impulse tubing and air supply/signal lines.
• Inspect installation of supports prior to cable tray installation.
• Inspection of cable tray/conduit installation prior to release for cable laying.
• Inspect UG stub-ups and instrument earthing of panels, cables etc.
• Inspect cable trench for sand bedding prior to cable laying and release each layer.
• Inspect cable segregation arrangement etc prior to back filling.
• Inspect cable glanding, termination, dressing of cable wiring inside each JB’s and local panels.
• Inspect installation of various control panels, consoles, desks.
• Inspect internal cable tray works prior to installation of cables.
• Inspect installation of various cables including system cables.
• Inspect installation of various F&G instruments, control panels.
• Witness calibration of each instrument as required by ITP/specifications.
• Witness pressure/leak testing of air supply/signal lines/pressure test of impulse tubes.
• Witness inspection/test related to analyser houses.
• Witness IR/continuity test of cables on the drum, prior to back filling trench, after glanding and termination.
• Witness testing of the F&G circuits and system as applicable and loop continuity checking.
• Verify completion of heat tracing for impulse tubes.
• Verify all inspections related each loop components have been carried out as per applicable ITP’s and documented.
•Always work Safety first.
•Material verification and Take store keeping of instrument material under control to be under a proper condition to avoid any damage or bad effect during warehousing
•Correct interpretation of equipment labels, IP Rating etc.
•Promptly report and document in all instances of nonconformance.
•Review Instrumentation works QA/QC Procedures/ITPs as per Project Specifications.
•Insure that all necessary inspections as identified in the approved Inspection and Test plan (ITP) and are attended by a suitable QA/QC Inspector.
•Ensure that the production quality being offered for inspection meets the client’s requirements and Monitor and report Key Performance.
•Ensure that all deviations from the Project Quality Program and the Company integrated management system (IMS) are documented and recorded.
•Coordinate the generation of client Requests for Inspections (RFI) where required
providing sufficient notice for Hold, witness and inspection Points.
•Review & check documents for instrument loop folder package prior to final walk down.
•Review final Dossiers documents if the attachment’s complete prior to handover.
•Responsible of E&I installation & inspection activities on the Site.
•Installation & inspection of instruments and electrical equipment’s and panels.
•Supervise the quality control function on site.
•Issuing, follow up and approval of NCR and MRS.
•Inspect Electrical & Instrumental Work carried out by the yard.
•Conducting different tests such as line check& loop tests carried out by the Yard.
•Monitoring, review and inspection of all major activities and progress of the E&I construction works.
•Interface with engineering, planning and procurement as well as other disciplines.
•Responsible for his own safety and others safety working around him.
•Responsible to have reasonable care towards the environment and contribute in energy savings and waste reduction.
bachelor of science in industrial technology major in electrical