محمود صقر

In the field of instrumentation maintenance, erection & commissioning of field instruments, DCS, PLC system for Oil & Gas sector.
- Provide engineering technical support for solving the technical issue that related to the instrument & control systems
- Distribution control system (DCS Yokogawa Centum CS3000),
- Emergency shutdown system(ESD Yokogawa Prosafe RS),
- Advanced process control (APC)
- Machine Monitoring System (Bently Nevada 3500/ vibration system1),
- Gas Turbine Protection & Control System (MarkVI).
- Steam turbine control system (Woodward 5009 controller),
- Anti-Surge (CCC) control system for compressor protection
- Metering Skid and Fire & Gas system.
- Integrated control system (ICS),
- Review & comment on control & instrumentation Suppliers/ vendors' technical quotation evaluation.
- Participate in the study of uncontrolled asset trips, repeated failures and chronic problems, in order to develop its root cause analysis.
- Participate in the roster duty to provide 24 hours maintenance key person, coordinate among the different maintenance disciplines.
- Prepare the PMs, the Job plan and determine the frequency for each PM. as per OEM manuals and apply the PMO \{Preventive Maintenance Optimization\} & RCM \{Risk Controlled Maintenance\} strategies.
- Prepare the Annual Budget (Operating & Capital) and submit to higher

Site & Job Title: Lead Instrument & Control Engineer at ENI Project on Zubair, Basra on Iraq from Jun 2017- till now
Job Description :
1-Responsible for execution of operation & maintenance of HP/LP Reciprocating Gas Compressor driven by Gas Engine
2-Executing standard maintenance schedule aiming at zero breakdown time in process control by implementing strategies in alignment with the initiatives and providing a clear sense of direction.
3-Responsible for preparing and achieving the all types of maintenance like Preventive, Corrective and Emergency maintenance for all instrumentation
4-Participate in operation work planning based on work order in the CMMS SAP PM system and control the execution of work order approved in CMMS SAP PM.
6-Investigation & dealing with troubleshooting of instruments failures during plant commissioning activities and start up this plants for all equipment such as, 30 gas compressors(Areal) driven by Gas Engine (Waukesha-L5794 GSI/L7044 GSI), 6 Solar gas turbine (MARS100) controlled by ALLEN-BRADLEY PLC RS logic 5000
•Performing all type of Maintenance (Preventive, Protective, and Emergency) for all types’ instrument items for the gas turbines and all utility units Like Water Treatment, Gas Compressor, Air Compressor, Black Start Diesel Generator (BSDG), and F&G systems for Gas Turbine Power Plant GTPP.
•Ability to write detailed repair reports as well as good verbal communication.
7-Supervision and Coordination of the operations involved in the execution of the maintenance Fire and Gas systems like Gas Detectors (H2S, CH4 and Flammable), Smoke Detectors and Heat Detectors (Honeywell, DET_TRONIC, General Monitors and Drager), and also, familiar with the deluge valve systems and dealing with the trouble shooting when required.
8-Field Diagnostics Check and Remote calibration using HART 375 & 475 Communicator.
9-Control Valves like On-OFF Valve, Divert Valve, Circulation Valve, and all type of Positioners like pneumatic, Smart (DVC 6000) calibration, installation, over hauling, fault finding and corrective and preventive maintenance like Masoneilan, Valtek, Fisher ABB and other manufacturer, MOV’s of Rotork Biffi Bench set Calibration and Stroke Checking.
10-Solving the Troubleshooting and maintenance of Field Instruments:
- Draft Pressure Transmitters, Differential Pressure Transmitters, Inline Pressure transmitter, Temperature Transmitters, DP Flow Transmitters, Vortex Flow Transmitters, Ultrasonic Flow Transmitters, Gamma Ray Level Transmitters, DP Level Transmitters, Float Type Level Transmitter, Ultrasonic Level Transmitter (Rosemount, Mobrey, Honeywell, Foxboro, GE, Masoneilan, Brooks Instrument)
- Thermocouple, RTD and Multiple Thermo-sensor Thermometer (MTT)
-Enraf and GSI Tank Gauging system, Entis Pro 2.4 operating software program.
Site & Job Title: Senior Instrument Engineer at Lukoil Project on West Qurna2, Basra, Iraq from Nov 2014- Jun 2017
Job Description:
1- Responsible for preparing and achieving the all types of maintenance like Preventive, Corrective and Emergency maintenance for all instrumentation items.
2- Participate in operation work planning based on work order in the CMMS SAP PM system.
3-Preparation of purchase requests for spare parts and consumable in CMMS SAP System
-Pneumatic Controllers (Pressure and Level).
-Enraf and GSI Tank Gauging system, Entis Pro 2.4 operating Software program.
10- Commissioning and start up verification for newly constructed
LUKOIL West Qurna, Basra, Iraq.
Following are details:-
-Eagle Quantum Premiere Fire and Gas Detection and Releasing System.
-Drager CC-Vision Calibration Operation And Maintenance.
-Protect•IR® Multispectrum IR Flame Detector X3301.
-XLS140 Intelligent Addressable Fire Alarm System.
-Honeywell Searchpoint Optima Plus Infrared Point Gas Detector Calibration Maintenance.
- Deluge valve system complete maintenance and commissioning, and dealing with trouble shooting when required.

Responsible for preparing and achieving the preventive and corrective maintenance work order for all instrumentation items which covers:-
1-Calibration and adjustment the field instruments like pressure, Temperature, level, flow transmitters and switches.
2-Testing, calibration and maintenance all types of control valves.
3-Maintaining the local panels including PLC’S and dealing with the trouble shooting for control system and for PLC’S SIEMENS SIMATIC S5 - 115H, SIMATIC S7 - 300 and ALLEN-BRADLEY PLC 5/20C, 5/40C.
4- Design and sizing valve selection for any types of control valves.
5-Design and build the control loop and select the field instruments like, pressure, temperature, level and flow transmitter and switches according to functional and performance specifications.
6-Performing the loop check, sequence check for the control panel including PLC’S
7-Maintenance for all types of the protection instruments for the gas turbines like over speed, over temperature, vibration modules and calibrating the Bentley Nevada system for vibration.
8-- Observing the operation of Tanks' gauging system and adjusting the Reading to match the actual tank level dealing with the trouble shooting when required.
9-Reviews the Bill of Quantities prepared by design engineers and contractors to ensure that in according to the drawings and specifications codes and standards.
10-Reviews the cost estimates submitted by contractor, and ensures that compliance with Agreement, Contract drawings, Specification and accuracy of Company requirements.
11-Preparation of Bill of Quantities based on Drawings and Specification.
12-Good knowledge of work safety activities in the plant such as: Work Permit, Equipment Isolation, Working at heights, Chemicals handling, Scaffolds erection, Confined space entry, etc.

1-Designed and Implemented the Upgraded the program PLC SIEMENS SIMATIC S5 - 115H to PLC program SIMATIC S7 - 317H for the Hydrogen Compressor GB - 302 A /B at AMOC site.
2-Designed and Implemented the Upgraded the control system for the OVER HEAD compressor (RC) at Abo-Sanan plant. To control with PLC system based on SIEMENS redundant S7-412H system connected to ET200M I/O station.
3-Design and sizing valve selection for any types of control valves.
4-Design and build the control loop and select the field instruments like, pressure, temperature, level and flow transmitter and switches according to functional and performance specifications.
5-Maintaining the local panels including PLC’S and dealing with the trouble shooting for control system and for PLC’S SIEMENS SIMATIC S5 - 115H, SIMATIC S7 - CPU 300U, 414-5H, Remote I/O ET200M and ALLEN-BRADLEY PLC 5/20C, 5/40C.
Responsible for preparing and achieving the preventive and corrective maintenance work order for all instrumentation items which covers:-

1-Calibration and adjustment the field instruments like pressure, Temperature, level, flow transmitters and switches.
2-Testing, calibration and maintenance all types of control valves.
3-Observing the operation of Tanks' gauging system and adjusting the Reading to match the actual tank level dealing with the trouble shooting when required.
6-Performing the I/O check and checking the program logic online and offline using PG 740 portable and making the necessary modifications in the program logics when required.
7-Starting up and downloading the program of the operating panel Siemens OP 17, OP27 using the program software PROTOL.
8-Commissioning, starting up, maintenance and trouble shooting of HANYWELL DCS system.
9-Carrying out the trouble shooting for the sequence machines and solving the problems for automation.
10-Adjusting and programming the AC inverters by setting the parameters.
11-Calibration and adjusting the weight scale for loading arm unit.
12-Carrying out the trouble shooting for the gas turbines including PLC’S and maintenance for all types of instruments like pressure, temperature, level, vibration switches.
13-Maintenance for all types of the protection instruments for the gas turbines like over speed, over temperature, vibration modules and calibrating the Bentley Nevada system for vibration.
14-Train the section's team in maintenance principles and troubleshooting techniques.
15-Testing and calibrating some types of analyzers like PH & Conduct.
16-Good knowledge of work safety activities in the plant such as: Work Permit, Equipment Isolation, Working at heights, Chemicals handling, Scaffolds erection, Confined space entry, etc.