E&I QA
Total years of experience :2 years, 4 Months
Responsibilities : Review IFC & AFC drawing and documents of instrumentation before installation, testing and
commissioning in accordance with specification, codes and standards conducts activities and inspections in
accordance to project quality control inspection plan, surveillance inspection of field instrumentation. Loop
checking from field instrument to main console monitoring of DCS system. Functional TESTING POWER
TRANSFORMERS
High-voltage transformers are some of the most important (and expensive) pieces of equipment required for
operating a power system. The purchase, preparation, assembly, operation and maintenance of transformers
represent a large expense to the power system.
CURRICULUM VITAE
8.1 OVERVIEW
When transformers are received from the factory or reallocated from another location it is necessary to
verify that each transformer is dry, no damage has occurred during shipping, internal connections have
not been loosened, the transformer’s ratio, polarity, and impedance agree with its nameplate, its major
insulation structure is intact, wiring insulation has not been bridged, and the transformer is ready for
service. Nameplate Data, Auxiliary Components and Wire Checks, Hand Meggering, Power eggering,
Lightning Arrestors, Temperature Devices. 4. Check and Megger all wiring point to point: Fans, umps,
alarms, heaters, tap changers, and all other devices on the transformer and nterconnecting cables 5. All
banks above 150 MVA should be vacuum dried. Do not apply test voltages to the winding during the
vacuum drying process. Make certain the terminals are shorted and grounded during oil circulation
because of the large amount of static charge that can build up on the winding. 6. After the tank has
been filled with oil, confirm that an oil sample was sent to the Chemical Lab and that its results are
entered in the bank test reports. Note the oil level and temperature at completion of filling. 7. Power
operate to verify proper rotation of pumps and fans and correct operation of the under load (UL) tap
changer, when provided. Also, check heater, alarms and all other devices for proper operation.
DEFINATION FOR THE : E&I QA/QC INSPECTOR OIL & GAS
REFIENRY PROJECT.
Job profile :
As responsible for the work in boiler & turbine with pneumatic and electronic instruments,
installation of supports brackets, airline, instrument tubing, tray work, pressure testing of
various instrument and airline, also involved in calibration of various instruments like Make
Honeywell and calibration of control valves and Make Fisher, Masoneilan wall take, prepare
loop testing procedure, and function test certificates of instruments, calibration all types of
proceed instrument during testing operation HONEYWELL CONSOLE TDC3000, during
loop checking inspects all DCS configuration process instruments commission fire & gas
instruments assist to vendor during start-up of package equipments, test ESD logic as per cause
and effect chart, complete knowledge of P & ID, ILD, location drawing and logic drawings.
NATURE OF WORK
Inspection & responsibility works for the instrumentation & electrical work for new control room and
inspection of all loop and instrument as QA/QC. Inspector, the applicable was fully responsible for all
QA/QC activities for instrumentation & electrical works, preparation of method statements, ITPS,
handover packages were some of the responsibilities the project scope involved installation, testing,
calibration and pre-commissioning of field instrument installation testing and pre-commissioning of
DCS, ESD system relocation, testing and pre-commissioning of fire detection system (UV/IR),
vibration monitoring, RDS telemetry system.
Excellent exposure to various system like DCS, PLC, RTU, fire & gas system, ESD system, turbine &
compressor system etc. associated with refinery, gas process plant petrochemical, offshore production
platform, fertilizer plant, oil and gas well heads.
Various calibration installation & testing procedures safety rules and regulations as per international
standards and instrumentation code e.g. API, ANSI, NEMA, ISA, QA/QC documentation like
CURRICULUM VITAE
inspection and plant, method statements, report forms, completions dossier, design and materials
approval statements etc. as per ISO project & schedule, design & engineering procurements,
construction & commissioning application developments & customers supports services.
JOB DESCRIPTION
Responsibility for:
Calibration of pneumatics electronics transmitter smart transmitters (HONEYWELL, ROSEMOUNT)
like PT, FT, TT, LT, DPT, level troll, type of gugages, controller recorder and repairing of instruments,
overhauling of pneumatics instruments, rotating instruments. In charge of field inspection for final
acceptance prior to mechanical completion. MCC certification of instrument as per approved quality
control plan and test plan in compliance to project specification and other relevant documents. The
above includes instrument bench calibration and functional check of various types of instrument such
as FLOW, LEVEL, Pressure and Temperature. Control valves, Transmitters, PRV and analytical
instruments. Work experience of installation wiring and loop checking for DCS, ESD, PLC, H2S
Sensor and, PDHMS. Data Assessment for Electrical Surge Protection Devices Assessment of
Hazardous Voltage/Current in Marinas, Boatyards and Floating Buildings Disaster Resiliency and
NFPA Codes and Standards Development of Fire Mitigations Solutions for PV Systems Installed on
Building Roofs - Phase 1 Hazard Assessment of Lithium Ion Battery Energy Storage Systems
Electrical fires report Influence of Damage and Degradation on Breakdown Voltage of NM Cables
Conducting Surveillance for Construction Activities and Site Inspection for the following Electrical
Site : REROUT OF H2S SENSSOR AFK DRILL SITE
Responsibilities : Review AFC drawing and documents of instrumentation before installation,
testing and commissioning in accordance with specification, codes and standards conducts
activities and inspections in accordance to project quality control inspection plan, surveillance
inspection of field instrumentation. Oman sohar refinery Inspection of 132, 66(, GIS)
33, 11, 6.6, kv and 415volt( MCC) switch gear panels including all kind of necessary test like
bus-bar insulation, hipot, ducter, CT, VT, ratio, polarity test.breaker insulation, relay function test
etc, assist to construction and Inspection of emergency generator 3.3 kv with insulation
resistance and polarization test. Inspection of 66, 33, 11, 6.6kv transformer including all kind of
necessary test .like winding insulation, hipot, tap changer ratio, vector group, dielectric oil test
etc .inspection of earth resistor with insulation, hipot test. Inspection and witness of cp work
like transformer rectifier, sacrificial, canister, zincpolarizationcoupon, magnesium anodes.
Bond box, junction box negative junction box for underground pipe vessels and tank.
.Inspection of cp anode cables and termination as per vendor drawing. Inspection of instrument
towards generator according the vendor P& ID. Witness of Hippo test for high voltage cable.
Inspection of oil skid heater, with insulation resistance test. Relay panel installation. Inspection
of Declaimer motors, panels, instruments at ship loader panels at the jetty area. Inspection of
ship loader motor and instruments such like coupling control switch limit switch. Backward
forward travel ultimate limit switch. Warning horn and lighting system. Inspection of area
network earthling and lightning protection of building. And earth pit as per drawing.
Preparation of MCCR mechanical completion checks record and area punch with client and
principle employee. Loop checking from field instrument to main console monitoring of DCS
system. Functional loop testing of ESD & fire & gas system. 132 kv substation complete
construction with all electrical equipment’s, including oil filtration for all transformer.
Transmission line complete installation/ gantry/ med vol. cable up to 35 kv with single core to
Over 10 Years 1 Months 9 Days abroad and Indian as a QC Inspector and Electrical Tech.
Supervision: Extensive experience in the field of QA/QC Inspector. Electrical & Instrumentation,
Engineering, Construction, Hook Up, Pre-commissioning and commissioning of various nature of
plant, exposure in oil & gas production and processing facilities, petrochemical plant.
In charge of field inspection for final acceptance prior to mechanical completion. MCC certification of
instrument as per approved quality control plan and test plan in compliance to project specification and
other relevant documents. The above includes instrument bench calibration and functional check of
various types of instrument such as FLOW, LEVEL, Pressure and Temperature. Control valves,
Transmitters, PRV and analytical instruments. Work experience of installation wiring and loop
checking for DCS, ESD, PLC, H2S Sensor and, PDHMS. Data Assessment for Electrical Surge
Protection Devices Assessment of Hazardous Voltage/Current in Marinas, Boatyards and Floating Buildings
Disaster Resiliency and NFPA Codes and Standards Development of Fire Mitigations Solutions for PV
Systems Installed on Building Roofs - Phase 1 Hazard Assessment of Lithium Ion Battery Energy Storage
Systems Electrical fires report Influence of Damage and Degradation on Breakdown Voltage of NM
Cables Conducting Surveillance for Construction Activities and Site Inspection for the following
Electrical Activities : - Preparation of Inspection and Test Plan, Construction Quality Procedure and
Method of Statement - Preparation and Submittal for RFI. - Review and Inspection of all Electrical
Material, prior to Installation. - Daily monitoring the Construction Activities. - Responsible for the over-
all implementation of Quality Control related electrical works accordance with project specifications
and Engineering Standards. - Verify the equipment and devices used in the project meets the required
specifications per project requirements, Standard and tested in accordance with the procedures.
- Monitor the Underground installations; check the required burial depth and spacing requirements to
adjacent installations, prior to backfilling. - Testing of cable meggaring and HI - POT test. - Inspection
of Electrical Equipment function test and Illumination level testing of lighting system. - Inspection of
electrical installation Panels Monitoring control panel wiring, Termination, cable routing & cable
Tray Installation.
- Verify all required inspection report and test records are systematically generated and compiled
according to the approved QC Procedures. - Coordinate with Client representatives regarding the
implementation and quality of works. - Inspection of Switch Gear Panel installation, Cable Termination
and Bus bar torque. - Installation of control panel marshaling panels and termination continuity and
CURRICULUM VITAE
Meggar test. - Insulation Resistance and Winding Resistance Testing of LV, MV motors.- Inspection of
Ground Rod and Grounding cable, as per Engineering Specification.
- Preparation of Electrical Inspection Reports - QA/QC Inspection witness for cathodic protection
system Underground pipe lines and Metal Tanks. Installation of Permanent Anodes, Temporary Mg
Anodes, LIDA Anode, Galvanic Anodes, Test station, AJB, NJB, MJB ASB, CJB, DJB, and Positive
Negative cable laying, and Termination, Installation and termination of Transformer rectifier, Witness
of HMWPE Cable Holiday Test and CP system Pre-Commissioning Activities. - Inspection of Heat
Tracing panel Installation, PT, RTD Junction Box Installation and Heat tracing cable laying and
meggaring. - Witness for Pre-commissioning of motor Solo Run activities.- Prepare the Motor Solo
Run test Package.- Witness of Motor Solo Run Test
- Provide sufficient feedback to QA/QC Manager on the day to day quality issues.- To supervise and
carry out effective implementation of work schedule to clear punch list.
SKILLS
Hands on experience in calibration, testing troubleshooting loop check and commissioning.
2) OBJECTIVE
I have worked for about 10 years 1 Months 9 Days in different organization as petrochemical
industries, refinery, power plant and fertilizer and OIL & GAS Constructions, Maintenances so on
have experience in inspection job in my field Electrical complete installation and testing
commissioning for all type of electrical equipements instrument, calibration, loop checking,
troubleshooting and termination.
Construction & maintenance annual shutdown turns around, field jobs and in workshop maintenance
job and also on fall under my field of activity. With and experience in hand. I can handle any
challenging job.
Responsibilities : Work on highly advances system like DCS, Honeywell, PLC,
(dry type transformer/ med vol. cable installation up to 240mm 3 core) TDC 3000, Honeywell,
with the new technology, total plant solutions (TPS) system vibration, monitoring, Inspection
of cable IRI test/Continuity at drum level. Inspection of sand bedding for the UG cable with
reference to trench details and duct bank schedule and cable schedule. Visual inspection of
cable puling equipment used etc. Inspection of cable dressing, cable ID tags as per the drawings
and inspection of cable entry schedule of the CCR, glanding and termination. Inspection of UG
cable top layer sand bedding ad grounding, lying of red tiles or warning mesh and back filling.
Inspection of meggering test of various types of power and control and instruments cables.
Unpacking inspection of al field mounted instruments and panel. Installation of J.boxes, stub-
up, glanding & termination. Inspection of cable tray/conduits for primary and secondary cables.
Farthing installation/Testing inspection for the system and all he instruments panel like
marshaling RTU and SCADA panel. Installation of stanchion, instruments tubing and leak test.
Inspection of bench calibration of instruments. Installation of control valves, air manifolds, air
tubing and leak test inspection. Inspection of secondary cable pulling /laying, glanding and
termination. Preparation of loop folders/packages. Conduct loop test. Co-coordinating with
loop checking team. Preparation of documents/dossier for final submission to the client’s
.participating in commissioning activities. Inter connection of the LDC/UCS & MIS system to
enable the exchange of real time and historic data and object between the three networks.
Provision of telephone call back modems to help diaghose and update the UCS/LDC & MIS
system through direct contact with supplier. A redundant fiber optics n/w as the real time
process highway for the UCS.the scope of work of the management information system (MIS)
includes fiber optics MIS highway n/w with notes linking UCS/MIS systems. Fiber optics node
(patch panel box) in each of the buildings allowing inter building communication between the
O-LAN based equipment installed in each of the buildings. And office local area n/w O-LAN
in each of the buildings utilizing conventional copper wire technology. Personal computer
stations connected to each O-LAN for communication via the MIS fiber optics n/w system.
Witness of fiber optics single /multimode splicing to the splice closer inside the man hole.
Witness of FO cable termination the patch panel and MIS communication panel. And
CURRICULUM VITAE
measurements of the path loss from one end by OTDR. Preparation of materials submittal record
book. Visit at the site for surveillance report during construction activities. Visit at the site with main client and
principle client for pre PAU/PAU INSPECTION .Fiber optic cable single mode/multimode splicing. Fiber optic
cable termination in the n/w panel. Assist of SRS to main distribution frame installation. Assist of exchange to
main distribution frame installation. System worked for preventive and corrective maintenance troubleshooting,
pre-commissioning, commissioning and startup of expansion project electronics transmitters, controller
Export Facilities Project, (Joint Venture of Kuwait Gulf Oil Company and Saudi Aramco Gulf
Operations) as a
QA/QC E&I Inspector (Aramco Approved). Works mainly on preparation of Loop
Packages, Inspection for calibration of instruments, field inspection as per Saudi Aramco
Engineering Standards. • Preparation for Project Documentation of QAQC activities and
Others.
• Review Engineering Technical issue such as Cable schedule and Route, Ladder /
Tray Installation and Fabrication, Scaffolding Erection and Provision of Manpower, Tools,
Equipment’s and Machinery at site. Data Assessment for Electrical Surge Protection Devices
• Review Construction Drawing for IFC (Issued for Construction).
• Job includes scheduling and monitoring manpower installation work at site as per
Standards, ITPS, project specs, Coordinate QA/QC activities such as Inspection in
Hazardous (zone-0, 1,
2) & Safe areas included detailed inspection of all EEX Certified equipment Inspection of
Certified Equipment’s for plants project work.
• Review field quality control procedure, making punch list, reports for inspection work
Involved as per their procedure & specification for inspection of material, instruments,
inspection
Of installation & Insulation Test for E&I Cable. Above and Under Ground cable laying activities,
Correct Cable gladding procedure. I am very much keen to work with growth oriented
organization, which accepts challenges & Make it happen. It’s the willingness to develop new
CURRICULUM VITAE
Skills, abilities; maturity-perhaps a little Wisdom even working under great talent, boosted me to
apply. If given an opportunity, I will serve my superiors with utmost dedication. Hope you
provide me the same. Extensive experience in the field of QA/QC Inspector. Electrical &
Instrumentation, Engineering, Construction, Hook Up, Pre-commissioning and commissioning of
various nature of plant, exposure in oil & gas production and processing facilities, petrochemical
plant.
In charge of field inspection for final acceptance prior to mechanical completion. MCC
certification of instrument as per approved quality control plan and test plan in compliance to
project specification and other relevant documents. The above includes instrument bench
calibration and functional check of various types of instrument such as FLOW, LEVEL, Pressure
and Temperature. Control valves, Transmitters, PRV and analytical instruments. Work
experience of installation wiring and loop checking for DCS, ESD, PLC, H2S Sensor and, PDHMS.
Data Assessment for Electrical Surge Protection Devices Assessment of Hazardous Voltage/Current
in Marinas, Boatyards and Floating Buildings Disaster Resiliency and NFPA Codes and Standards
Development of Fire Mitigations Solutions for PV Systems Installed on Building Roofs - Phase 1 Hazard
Assessment of Lithium Ion Battery Energy Storage Systems Electrical fires report Influence of Damage and
Degradation on Breakdown Voltage of NM Cables Conducting Surveillance for Construction Activities and
Site Inspection for the following Electrical Activities : - Preparation of Inspection and Test Plan,
Construction Quality Procedure and Method of Statement - Preparation and Submittal for RFI. -
Review and Inspection of all Electrical Material, prior to Installation. - Daily monitoring the
Construction Activities. - Responsible for the over-all implementation of Quality Control related
electrical works accordance with project specifications and Engineering Standards. - Verify the
equipment and devices used in the project meets the required specifications per project requirements,
Standard and tested in accordance with the procedures.
- Monitor the Underground installations; check the required burial depth and spacing requirements to
adjacent installations, prior to backfilling. - Testing of cable meggaring and HI - POT test. - Inspection
of Electrical Equipment function test and Illumination level testing of lighting system. - Inspection of
electrical installation Panels Monitoring control panel wiring, Termination, cable routing & cable
Tray Installation.
- Verify all required inspection report and test records are systematically generated and compiled
according to the approved QC Procedures. - Coordinate with Client representatives regarding the
implementation and quality of works. - Inspection of Switch Gear Panel installation, Cable Termination
and Bus bar torque. - Installation of control panel marshaling panels and termination continuity and
Meggar test. - Insulation Resistance and Winding Resistance Testing of LV, MV motors.- Inspection of
Ground Rod and Grounding cable, as per Engineering Specification.
- Preparation of Electrical Inspection Reports - QA/QC Inspection witness for cathodic protection
system Underground pipe lines and Metal Tanks. Installation of Permanent Anodes, Temporary Mg
Anodes, LIDA Anode, Galvanic Anodes, Test station, AJB, NJB, MJB ASB, CJB, DJB, and Positive
Negative cable laying, and Termination, Installation and termination of Transformer rectifier, Witness
of HMWPE Cable Holiday Test and CP system Pre-Commissioning Activities. - Inspection of Heat
Tracing panel Installation, PT, RTD Junction Box Installation and Heat tracing cable laying and
meggaring. - Witness for Pre-commissioning of motor Solo Run activities
Thanks & Regards
MOHAMMAD PRINCE GANI
INSPECTION: FOR:
Installation, modification, testing, loop checking identify troubleshooting, continuity testing, signal
checking, commissioning & pre-commissioning sequence checking, Meggering, glanding and
termination.
Performed inspection covering phases of instrumentation installation of field instruments, junction
boxes, conduit and cable tray, grounding, instruments installation, instrument tubing fire & gas
detection system and control system, also performed quality control inspection covering of calibration,
loop checking of field instrumentation (LT, PT, PI, FT, FS, TE etc), MOV, H2S Gas detectors etc
in
in The Year of
in The Year of
in The Year of
COVER LETTER: (E&I QA/QC INSPECTOR) MOHAMMAD PRINCE GANI Dear Sir, I am Mohammad Prince Gani
COVER LETTER: (E&I QA/QC INSPECTOR) MOHAMMAD PRINCE GANI Dear Sir, I am Mohammad Prince Gani