Hussein khalifa

• Lead electric maintenance team for all plant day-to-day activities and
ensure the operation readiness for all plant electrical equipment.
• Drive execution of continuous improvement of existing equipment
maintenance strategies including identification & tracking of
equipment Bad Actors, driving of proactive maintenance focus
through on-time PM execution & PM optimization, periodic review &
optimization of equipment critical spare parts strategies, facilitation
of root cause analysis (RCA) studies related to equipment failure
events, and participation in the MOC & capital project review
processes.
• Ensures compliance to plant safe work practices, policies and
procedures including management of change (MOC).
• Manage and drive implementation of maintenance and reliability
procedures including periodic review & revision of maintenance
procedures, and periodic auditing (Go & See) of maintenance &
reliability procedure compliance.
• Led numerous Reliability, Availability and Maintainability Analysis
(RAM) in maintenance section.
• Conducts and directs regular audits including risk assessments and
safety reviews and ensure that actions mentioned in the audit report
are compiled and closed.
• Use corrective maintenance prioritization tool (CMPT) to prioritize
the corrective failures and trips.
• prepare/developing asset structure, SCE review and implementation,
and bill of materials (BoM) using the equipments drawings, circuit
diagrams, P&IDs, operation, and maintenance manual of OEMs.
• Carried out Ex-Inspection electrical, Instrumentation &
Communication equipment in accordance to standard IEC‐60079‐17 /
IEC 60079‐14 for all zones and issued detailed inspection report
according to CMMS SAP Maintenance plan.
• Prepare total and partial shutdown procedures for the power plant
and supervise execution.
• Retrofitting of various numerical relays to old panels with necessary
schemes and wiring.

• Witnessing all SAT (Site acceptance test), pre-commissioning and commissioning phase of different Switchgear components for new project (C.R.P Carbon reduction plant) at Bed-3 site.
• Working with SAP (Systems, Applications and Products)
• In hand experience with all H.V and L.V Switchgear.
• In hand experience with protection systems function test through injection with different test sets and troubleshooting.
• Working with different test sets from megger products.
• In hand experience with U.P.S and D.C Battery charger.
• In hand experience with L.M.P (load management panel) controlled with P.L.C.
• General experience of power generation turbines for both gas and diesel.
• In hand experience with power generators Caterpillar and Cummins.
• General experience in E.S.P. Electrical submersible pumps systems used for oil wells.
• In hand experience with Solar Cells used on gas Wells for powering air compressors used for hydraulic valves protection.

• Commissioning and Testing for electrical equipment including but not
limited to a HV/LV Switchgear AIS, oil and dry type transformers, CTs and
VTs, variable speed drive VSD, generators, motors, UPS, Heat Trace and
Ensure that installation of electrical equipment as per applicable standard
(DEP shell standard and IEC)
• Apply approved final settings of each protection relay IED carry out testing
for relay settings for different protection functions as (overcurrent.
instantaneous and inverse time (50/51) earth fault protection, differential
87, restricted earth fault 64, distance protection21 for ABB (REF611,
REF612, Rem543, Reg630) and schneider relay Sepam (seriesS80. T81).
etc.) and also testing electrical interlocking and logic diagram.
• Raise the site query (SQ) and change request to modify in the design of the
project to comply with our DEP shell standard and our ESR (Electrical Safety
Rules) requirements.
• Prepare all marked up drawings in preparation for the release as-built
drawings.
• Create punch list for each system and sub-systems after the pre
commissioning, commissioning and start up. Ensure that all system check
sheets and punch lists have been reviewed, and cleared before start-up.
• Check and test all loop signals between HV/LV switchboard or MCS-VSD
RCU-DCS to be ready before start up.
• Review and update checklists for mechanical completion, pre
commissioning and commissioning phase.
• Prepare start-up procedure to check overall electrical system before
energization.

• Carry out preventive and corrective maintenance (PM&CM) for electrical
equipment including but not limited to a HV/LV Switchgear, Generators, Motors,
power transformers, Heat trace systems, UPS, Battery charger, LV/ MV VSD
• Implementation of comprehensive Isolation / de-isolation and Switching programs
for HV/LV Electrical Equipment.
• Execution SAP activities including but not limited to a creation notification, work
order, external service and material evaluation.
• Carry out injection testing for protection relays of HV/LV electrical equipment.
• Carry out function operation testing for power management system.
• Create and prepare permit to work PTW for electrical daily activities of PM & CM.
• Comply with HSE & ESR electrical safety rules during work execution.

working with PLC and Scada systems and make network .
• Plc Programming using Unity pro Schneider Electric
• Dealing with SCADA program Vijeo citect Schneider Electric