june remigio

connection pipes from main fire pump.
2.) Design drawing layout of Fire Alarm initiating devices such as smoke detectors, manual pull station & interface modules.
3.) Design drawing layout of Voice Evacuation speakers & horn strobe.
4.) Design drawing layout of Emergency & Exit lighting connected to central battery.
5.) Design drawing layout of Life Safety 1& 2 hour fire rated wall, exit staircase, exit separation, diagonal distance, travel distance within the unit, dead end, and overall travel distances.
6.) Design drawing layout of Life safety according to minimum passageway width, room size with minimum 2 exits.
7.) Design drawing layout of Occupancy classification with room occupant load calcualtion
such as smoke detector, heat detector, manual pull station, elevator recall smoke detector, heat of rise detector and interface modules.
2.) Design drawing layout of Voice Evacuation System with standard specification, parameters and procedures such as the distances between
speakers, horns and strobe in every designated areas of building.
3.) Design drawing layout of Emergency Lighting System with standard distances of emergency luminaires and exit lights.
4.) Exit escape route and main egress for providing exit lights and arrow signs.
5.) Schematic /riser diagrams connection from addressable fire alarm panel distributed through all initiating and notification devices.
6.) Access control system door hardware.
7.) Security Cameras, Door Access Control System, Wireless Access Point, Nurse Call, Public Address, Design Layout.

8.) Basic lighting and power socket outlet fixtures layout and cicuit wiring layout.
9.) Flatshot perspective Isometric 3D modeling of installation details.
10.) Revit modeling layout of power socket outlet, lighting, DB, SMDB panel, meter reading and isolator for HVAC equipment.
11.) Revit creating 3D family & 2D annotation modeling with parameters for electrical & plumbing fixture layout application.
12.) Revit setup project browser arrangement, sections, copy monitor floors, schedules, title sheets & manage worksets, visibility graphics, layout plans & object parameters settings.
13.) Revit sheet file managing revision numbers, matchline, publishing PDF & exporting CAD submission.
14.) Manage Project Browser, sub-classification discipline, floor plan view with scope box, assigning different visibility graphics template for each viewport.
15.) Select Element with filters, assigning colors, object isolation, hiding particular objects using Visibility Graphic Filters.
16.) Project navigation, view creation, element selection and manipulation using Rotate, Move, Copy, Trim, Offset, Split, Align, Scale, etc.
17.) Controlling element visibility, automating view style by using override graphics in View.
18.) Selecting the project units, MEP settings, linking & importing files, copy Monitor, & coordination review.
19.) Basic knowledge in building elements such as wall, floors, columns, roofs & ceilings.
20.) Equipment, fixtures and fittings which is level hosted, free standing or system hosted elements.
21.) Component placement and create system type filter.
22.) Linking CAD file with general installation details, riser diagrams, site plan, symbols and notes and drawing list.
23.) Geometry formation and in-place families such as Extrusion, Blend, Revolve, Sweep & Sweep Blend.
24.) Electrical systems and circuit using Electrical service type filter, lighting fixture family modeling and annotations.
25.) 2D draughting annotation, material tags and callout, detail lines, region, dimensions, text and leader line.
26.) Family editing by using dimension parameters, sub type family, 2D lineworks, 3D geometry, sub categorize and define types.

MEP electrical design layout

of work: CCTV CAMERA, ACCESS CONTROL AND INTRUDER ALARMS SYSTEM+ CAD 3D MODELING
1.) Detail drawing and section of Data Control center and console data (3D MODEL 3DSMAX VRAY RENDERING)
2.) Detail drawing of car park road blockers, exit gate barriers, & Gunnebo Turnstiles.
3.) Layout drawings and schematic diagram of access control system and intruder alarm system.
4.) Layout drawings & schematic diagram of CCTV camera, Access control & Intrusion Detection System.
5.) Fabrication drawings of mechanical parts assembly of camera service box, mounting brackets, & other miscellaneous mechanical parts (2D/3D).
6.) Layout of RG59, CAT-6, RS485, Fiber optics & other data cable routing fed from rack server devices.
7.) Architectural plans & sections of control rooms & camera orientations.
8.) Isometric views and details of Door Access Control System.
9.) CAD standard layers, line types, colors, blocks, customize attributes, interface, xrefs, line types, exporting &
Importing files and links, and editing command parameters.
10.) Modeling various 3D objects and sole profile into flatten isometric and perspective model.

work: LOW VOLTAGE MDB, SMDB, FDB & RELAY PANEL
1.) 3D MODELING + DETAIL of G.E mechanical parts fabrication assembly drawing of LV electrical panel.
2.) Drawing of Low Voltage MDB & SMDB Electrical Panel Switch gear.
3.) Drawing of single line diagram for low voltage AC Switchboard.
4.) Design drawing of Relay Panel Protection & Control / Wiring Schematic diagram.
5.) Drawing of electrical components Block symbols.
6.) Analyze and draw of electrical wiring diagram from MDB main incomer ( air circuit breaker)

DISCIPLINE: FIRE PROTECTION SYSTEM & FIRE ALARM

1.) Design of Sprinkler Layout and Riser Diagrams based on NFPA-13 pipe schedule and design parameter such as:
a.) Hazard occupancy & temperature rating of sprinkler.
b.) System Area Limitation & Sprinkler Coverage.
c.) Equivalent Pipe Length.
d.) C-values & Pipe Schedule
e.) Standpipe & Hose System Guide as per NFPA 14
f.) Portable extinguisher placement parameter as per NFPA 10
g.) Fire Pump Controllers as per NFPA 20.
h.) Deluge Foam Sprinkler System as per NFPA 11 & 16.
2.) Drawing of sprinkler heads typical detail such as:
a.) Type 1&2 Upright Sprinkler Head: pendent / recessed & concealed sprinkler head .
b.) Side Wall Sprinkler and window sprinkler head detail.
c.) Garbage chute sprinkler head & sprinkler head guard detail.
inspector test drain connection, dry pipe valve, deluge valve & pre-action valve.
2.) Drawing of isometric view of entire fire protection piping system in a buildings
3.) Drawing layout of Fire Alarm System with standard parameters and procedures of smoke detectors, heat detectors, control / monitor
modules and manual pull stations in every floor based on NFPA 72.
4.) Drawing layout of Voice Evacuation System with standard specification, parameters and procedures such as the distances between
speakers, horns and strobe in every designated areas of building.
5.) Design drawing layout of Emergency Lighting System with standard distances of emergency luminaires and exit lights.
6.) Drawing design concept of non-maintain and maintain emergency light self-contained batteries.
7.) Analyze the path of exit escape route and main egress for providing exit lights and arrow signs.
8.) Drawing of Schematic Diagram of Fire Alarm System where the FACP receives information from environmental sensors designed to
detect changes associated with fire, monitors their operational integrity and provides for automatic control of equipment, and transmission of
information necessary to prepare the facility for fire based on a predetermined sequence.
9.) Drawing of Voice Evacuation system that linked from a Voice Alarm Control and Indicating Equipment to Fire Alarm Control Panel
with fire alarm notification appliance .
10.) Drawing of emergency luminaires at mandatory points of emphasis to site escape at each intersection of corridors, at exit doors, at each
change of directions, on each staircase, at firefighting equipment, at each fire alarm call points, at each first aid post, and at other change level.
11.) Central battery system drawing of riser diagrams to centralize and distribute the slave luminaires and conversion modules to be utilize
for both normal and emergency lighting operation.

1.) Prepare As-Built Drawing of Whole podium, tower level, penthouse, and Lift Machine Room prior to submission based on actual inspection
on site and make comments for every pipe connection according to NFPA procedure.
2.) Design of Sprinkler Layout based on NFPA pipe schedule and design parameter.
3.) Equipment Pressure Valve detailing and preparing shop drawing.
4.) CO2 Gas Suppression System and total flooding system in which piping shall be design as per NFPA-12 to deliver the rate of application at each nozzle.
5.) FM200 inert gas fire suppression, detection system layout, & sequence of operation.
6.) Double Interlock Pre-Action System sequence of operation.

Prepares shop/detail drawings 2D / 3D .
a. excavation works - Electrical Duct banks d. installation of Lighting Fixtures & Accessories\
b. construction of High Mast Pole Foundation e. wiring and termination
c. construction of Manhole & Section
2.) Familiar with structural sections and profiles, different types of steel, welding requirements, and symbols and other engineering standards.
3.) Conducts civil and detail surveying at the site prior to making plan and layout of the plant
4.) Implements ISO 9001 Standards.
5.) Draws and design the floor plans, interior, frames, and foundations for control rooms, shops, and portable offices.
6.) Secure all company documents at all times./ Controls approved drawings.
7.) Performs general drafting works which includes electrical, fabrication and some miscellaneous drawings
8.) Excavation, section, and profiles of electrical ductbank, telephone lines, and plumbing through accessroads.

Will be responsible for the encoding in CAD 2D / 3D (autocad) of all existing and incoming drafts, designs,
drawings as may be required.
2.) Must ensure that all detailed drawings and instructions released for production (fabrication & machining) are true,
correct and accurate as per sample, sketch of engineer or customer and in any way(s) be reliable-basis.
3.) Will provide technical assistance to Sales Engineers, / Supervisors, and Administration Dept. as may be required.
This covers designing chores of not so complicated designs say jigs and fixtures, carts and trolleys, cannisters and bins, reels, etc.
Also with the assistance or instruction from Superior/s, may be allowed to do more complicated job as long as it may be necessary
and time and situation ask and requires for it.
4.) Must ensure that drawings released for production must truly checked, noted and approved by proper signatories as per ISO standard.
5.) Must abide by company rules and regulations regarding proper usage of drawing documentations or ISO standards e.g, proper encoding
or sequential usage of controlled drawings numbers and other drawing/ documentation.

1. Primary duty is to draw the mechanical objects (work piece to be fabricate) in AUTOCAD and transfer to CADCAM to make tool path .
2. Assuring the output meets the company’s required specification.
3. Analyze the drawings and study the process before set-up the machine.
4. Check and edit programs if necessary (using Master Cam Mill V9) and transmit it to CNC machine memory.
5. Check the parameters (on the programs) to be used on the materials required to machine.
6. Preparation of cutting tools for a necessary parts.
7. Set-up the work piece using a correct position, proper Work Coordinate System(WCS).
8. Performs a machining operation on computer numerical control (CNC) machine.
9. Adjust and change machine settings based on specified requirements.
10. Check the status of the cutting tools and the chips produced by the cutters.
11. Preventive maintenance of machine of at least every 6 months.