Malik Awais Hayat

Senior E&I Engineer with major experience in E&I Quality assurance/control and construction of EPCC
Projects in Oil & Gas and Renewable Energy. Major Areas of expertise include:
EX01, EX02, EX03, EX04 Equipment & Systems Certifications
E&I QA/QC Documentation (QC Procedures, Inspection & Testing Reports, ITPs)
Quality Inspections, NCRs, SORs handling & Reporting
Monitoring, Planning and Inspection for scope of work area assigned.
Strictly follow IEC 60079-17, IEC 60079-17 “Electrical installations, selection and erection for
Hazards Area”.
Daily Surveillance in Site for Quality related Issues.
Maintain close liaison and good relationship with Third party & Client.
Raising Non Conformance report against the jobs which are not complying with company Standards
and Specifications.
Co-ordination with work supervisor for site construction activities.
Insisting the people and follow company HSE rules and Regulations in Site and Living areas.

• Working as a Lead Instrument Engineer at 750MW Solar power Plant project (Dubai)
• Preparation/ review material take-offs/BOQs for next phase of project
• Preparing Technical Queries, Technical recommendations and modifications in Design as per site conditions
• Interpretation of P&IDs, Loop Circuit diagrams, Electrical Wiring diagrams, Instrumentation data sheets, Logic diagrams, Cable routing layouts, Hook-up diagram for construction team.
• Follow up with the procurement team for the prompt arrival of project materials.
• Workforce, material & equipment quantity assessment for project execution
• Discussions with company counterparts about the procedures revise and improve documents to get approval from the company.
• Installation of all type panels/Cabinet along with all type of Instruments e.g. Transmitters, valves & Analyzers
• Installation of heat tracing and heat tracing panels in power block area of the power plant.

• Working as an E&I Engineer at ADNOC Ruwais Refinery (RRE) Sulphur Recovery unit (Unit 106)
• Preparation/ review material take-offs/BOQs
• Preparing Technical Queries, Technical recommendations
• Follow up with the procurement team for the prompt arrival of project materials.
• Workforce, material & equipment quantity assessment for project execution and bidding.
• Preparation work procedures, method statements, inspection test plan in accordance with project requirements.
• Interpretation of P&IDs, Loop Circuit diagrams, Electrical Wiring diagrams, Instrumentation data sheets, Logic diagrams, Cable routing layouts, Hook-up diagram for construction team.
• Installation of all type panels/Cabinet e.g. DCS, ESD, BMS, GDS, MCMS UPS etc.
• Installations of cable tray, cable laying along with cable terminations and final Testing, Instrument Loop testing and Motors Solo Run.
• Installation of the Cathodic Protection system
• Installation of all type of Instruments e.g. Transmitters, Analyzers, Gas Detectors etc.
• Installation of Impulse/Airline tubing and supervise the leak testing.
• Installation of Operating work station, Elco cables, Ethernet cables, Fiber optic cables etc. as per approved drawings.
• Installation of Toxic Gas detectors and CCTV Surveillance Camera and FOC Fiber optic cable laying
• Energize the DCS, ESD, GDS, BMS, and MCMS with the coordination of vendors and end users after the testing of powers cables, internal wiring and Earthing system.
• Preparation of the loop folders.
• Simple and Complex Loop Testing as per approved Instrument data sheets, ILD, P&ID, IO List, Alarm set point and Sequence input documents.
• Take Active Part in the MC walk down with Client Representatives (Do the Pre walk down and make sure everything is ready for MC walk down by capturing all flaws if any; into internal punch list).

Major Responsibilities:
• Worked as an Instrument Engineer at Descon Engineering
• Preparation work procedures, method statements
• Prepare/review the as-built mark-ups prepared at the site.
• Identify possible clash point with other disciplined bases or actual site condition and design drawing as well as implementing possible alternative without compromising specification and Engineering standard.
• Establish the Calibration lab and calibrate the all types of transmitters, switches, valves etc.
• Maintain the instrument calibration record and also make sure the Instrument calibration should be as per standard and project specification.
• Prepare the method statement of all activities.
• Monitoring and Reporting of discipline wise daily/weekly progress against work plan to the company and clients.
• Handling client walk down for mechanical completion & ready for commissioning.
• Functional testing as per approved cause and effect diagram, Sequence input documents, operating and control philosophy etc.
• To ensure that all performed activities conform to engineering design and client’s criteria and are carried out without compromising QHSE (Quality, Health, Safety and Environment) and play a dominant role in its significant improvement.

Work on oil&gas wellhead site and works in instrument and power section
• Install the Cathodic Protection system along with main pipeline and at wellhead points.
• Installation along with testing and commissioning of Fire Alarm and Addressing System.
• Installation of H2S detectors and MPFM and (multiphase Flow Metering) and CCTV Surveillance Camera and FOC Fiber optic cable laying
• Installation of OHPL Lines and poles with Transformers installation and Electrical & Instrument cable laying

Worked on Gas plants and Power plants involving Steam turbines, generators, Transformers and Switchgear Installation and Instruments installation as per their hookups.

Working as an E & I Engineer in Dandot cement and Lead the team for plant maintenance and shut downs