muhammad ali bilal

Jafurah wellhead pipeline project Saudi Arabia

SGCP Harad pipeline project

JAZAN Refinery project 2018

MECHANICAL INSPECTOR
NAIMAT GAS FIELD TANDO ADAM PAKISTAN

shutdowns QP Q.CHEM and SHELL

shutdown QAFAC.

Employer: DESCON, Abu Dhabi.-Habshan project
Designation Mechanical Asst. Engineer
Duration 22/01/2012 to till date
TAKREER Ruwais Refinery Division Shutdown.

Employer: DESCON, Abu Dhabi.-Shutdown project
Designation Mechanical Asst. Engineer
Duration 26-01-2012 to 21-04-2012

(in Gulf & Pakistan)
INTIGRATED GAS DEVELOPMENT PROJECT (HABSHAN-5)
Employer: DESCON, Abu Dhabi.-Habshan project

Designation Mechanical Asst. Engineer
Duration 22/01/2012 to till date

TAKREER Ruwais Refinery Division Shutdown.
Employer: DESCON, Abu Dhabi.-Shutdown project
Designation Mechanical Asst. Engineer
Duration 26-01-2012 to 21-04-2012


WORKING EXPERIENCE; (Pakistan)
PAK-AMERCAN FERTILIZER (Sikandrabad Mianwali) PAKISTAN.

Employer: DESCON, Shutdown project
Designation Mechanical Supervisor
Duration 05-12-2010 26-01-2011

STUDY TRAINING
Manzlai Gas Project Kohat Pakistan.
Employer: DESCON, Kohat
Designation: Material Coordinator

PAKISTAN PETROLIUM LIMITED SHUTDOWN (DOLTALA) RAWALPINDI

Employer: ENGINEERING KINETICS Ltd.
Designation: Asst. Supervisor.
Duration: 2-7 2008 11-7 2008
ATTOCK OIL FIELD (RAWALPINDI) Pakistan.

Employer: ENGINEERING KINETICS Ltd
Designation Mechanical Supervisor
Duration July 2007 to May 2008


Heat Exchanger
➢ Shutdown preparation
➢ Isolate the valves
➢ Blinding as per the blind list
➢ Remove the channel cover / channel head
➢ Remove floating head unit
➢ Remove the tube bundle (if necessary)
➢ Shell internal cleaning using power tools
➢ Inspection of shell side
➢ Hydro jetting of tube bundle & inspection
➢ Tube bundle fix back after inspection
➢ Fix test ring for shell side hydro test
➢ Re install floating head after cleaning & inspection
➢ Hydro testing of shell side
➢ Channel cover fix back after cleaning & inspection
➢ Hydro testing of tube side, floating head unit
➢ Remove the spool for Hydro testing, (if necessary)
➢ Final Inspection & box up
➢ De-blinding


Fin fan (Air cooler)
➢ Shutdown preparation
➢ Isolate the valves
➢ Blinding as per the blind list
➢ Remove the tubes plug (both side)
➢ Pre inspection by Qc department
➢ Tray fixing for hydro jetting (both side)
➢ Hydro jetting all tubes
➢ Air blowing
➢ Re-tubing, tube bundle replacement ( if necessary)
➢ Inspection after air blowing
➢ IRIS (internal rotary inspection system) test ( if necessary)
➢ All plugs are re-install
➢ Hydro testing of tube bundle & final inspection
➢ Box up
➢ De-blinding.

Tank & vessels
➢ Drain the oil from oil tank using vacuum trucks, then water flushing, air flushing using BA (Breathing apparatus)
➢ Nitrogen (N2) purging, gas testing
➢ Internal cleaning using hand/power tools
➢ Internal welding, grinding
➢ Report to QC for Internal inspection
➢ After inspection close the man way
➢ Shell cleaning using internal buffing
➢ Open the Man Way for internal cleaning & inspection of vessel
➢ Remove the Demister & fix back after cleaning
➢ Inspection & box up

Piping
➢ Receiving Plant drawings, Isometric drawings from Engineer for the pipeline installation work.
➢ Checking of dimensional measurements in the place where piping has to be erected/fabricated as per the Isometric drawings

➢ With the help of Fabricators and Fitters cut the required length of the pipe, make beveling and give fit up.

➢ Fit-up reports submitted to QC for Inspection.

➢ Install pipe fitments drawing and Observe Valve, Strainer orientation according to the Isometric and check for the Horizontal and Vertical rolling.


➢ After welding and inspection of NDT Hydro testing of the lines will be carried out.

➢ Done blinding in required places, remove control valves, check valves and replace with spools. Select gauge meter according to the pressure range. Open the Vent and start water filling from the drain side with the help of manifold.

➢ Further carryout and hold as per the QC instructions.

➢ Involved in steam piping (alloy steel) connecting to steam turbine, drain lines, lube oil lines (SS), condensate line & cooling water with supports to adjust its expansions.
➢ Fabrication & erection of gas plant pipe line as per site condition.
➢ Installation of Pipe spools in the running plant with safety and quality.
➢ Hydro testing of pipes & commissioning
➢ Installation of different types of Valves
➢ Erection of Pipe supports
➢ Pre-commissioning and Commissioning
➢ Controlling of Manpower
➢ Erection of Pipes in existing units with all safety measures.
➢ Planning for necessary Tools and Equipments
➢ Fabrication, testing, erection and commissioning of underground piping
➢ Plan and carry out tie in joints during unit and Refinery Shut downs.
➢ Fabrication, testing, erection and commissioning of process and utility piping in the running plant
➢ Check the site condition before fabrication & erection.
➢ Attending all punch list points until handover to client
➢ Conversant with checking of Fit ups, welding,
➢ Fully conversant with the preparation of BOM from Isometric, Plant and P&ID Drawings
Valves

➢ Pullout pressure relief valve, pressure safety valve & Reinstall after calibration
➢ Remove pressure control valve, Non-Return valve
➢ Blindin

INTIGRATED GAS DEVELOPMENT PROJECT (HABSHAN-5)